RISCO Group IR Beam 71 Outdoor Detector - Manual (Page 2)

‐2‐
5. Terminal Block 7. Response Time
• POWER Input: 10V~28VDC (non polar)
•
ALARM Output: NC, 30VDC/0.5A
•
TAMPER
6. Beam (Viewfinder) Adjustment
1. After confirming detector
mounting location, adjust the
reflector angle using the
viewfinders. 2. Using the viewfinders, adjust
reflectorʹs location to be within
the detection range of the
opposite detector.
3. To adjust the axis angle, turn the axis left or right side and up or
downward with a screwdriver.
If the opposite detector is not
shown clearly, attach a white
paper cover on the back of the
opposite detector. The distance
between the installer and the
viewfinder should be about 3‐
5cm (1.1ʺ‐1.9ʺ) to observe the
opposite detector clearly.
The Response period adjustment VR allows you to match the
sensitivity to the surroundings and avoid false alarms. Slower settings
reduce sensitivity.
1
3.5
6
VR indicator 1 ~ 2 2 ~ 3 3 ~ 4 4 ~ 5
(Default) 5 ~ 6
Detection type Quick
running Jogging Quick
pace Normal
pace Slow
pace
Detection speed 0.05sec 0.1sec 0.2sec 0.35sec 0.5sec
8. Technical Specifications
Model Beam 7115 Beam 7140
Detection Method Infrared photoelectric
Detection Range (Outdoor) 15m (50ft) 40m (130ft)
Detection Range (Indoor) 30m (98ft) 80m (262ft)
Response Period 0.05sec ‐ 0.5sec
Alarm Period Receiver: Standby‐LED is “OFF”,
Alarm‐LED is “ON”
Transmitter: LED is “ON” in normal situation
Alarm Output Standby: short, Alarm: disconnection
Contact Point: 30VDC/0.5A,
resistance:2.2Ω
Optical Axis Adjustment range Horizontal: ±90°, Vertical: ±5°
Power Input 10 ~ 28VDC (non‐polarity)
Power consumption Receiver: 16mA, Transmitter: 6mA, ±3mA
Tamper Cover removal
IP Rating IP44
Weight 624g (1.3lb)
Operating Temperature ‐20°C to +55°C (‐4°F to 131°F)
Storage Temperature ‐25°C to +60°C (13°F to 140°F)
Material ABS resin, Polycarbonate
Fine adjustment of an optical axis:
An error can be caused in the installer’s field of vision. So, fine
adjustment must be conducted using a built‐in monitor jack and a
tester.
4. Fine adjustment method:
(1) Insert “+” on tester to receiver’s positive voltage, “‐”on tester
should connect to “‐” on receiver. Turn the receiverʹs reflector to the
right or left so tester voltage is maximized. Avoid blocking the
reflector with your hands.
(2) Refer to the table below for tester indicated voltage and reliability.
For maximum output, perform fine adjustment. Preferably, adjust
tester voltage to high sensitivity.(Power input: 12VDC)
Tester
indicated
voltage
Sensitivity
(outdoor)
Sensitivity
(indoor)
Over 3.1V High
Over 2.7V Satisfactory
High
Over 2.2V Average Satisfactory
Over 1.0V Average
Below 1.0V
Needs
adjustment Needs adjustment
9. External Dimension
(2.4")
62mm
(2.5")
63.5mm
RISCO Group Limited Warranty
RISCO Group and its subsidiaries and affiliates (ʺSellerʺ) warrants its products to be free from defects in materials and
workmanship under normal use for 24 months from the date of production. Because Seller does not install or connect
the product and because the product may be used in conjunction with products not manufactured by the Seller, Seller
cannot guarantee the performance of the security system which uses this product. Sellerʹs obligation and liability under
this warranty is expressly limited to repairing and replacing, at Sellerʹs option, within a reasonable time after the date of
delivery, any product not meeting the specifications. Seller makes no other warranty, expressed or implied, and makes
no warranty of merchantability or of fitness for any particular purpose. In no case shall seller be liable for any
consequential or incidental damages for breach of this or any other warranty, expressed or implied, or upon any other
basis of liability whatsoever. Sellerʹs obligation under this warranty shall not include any transportation charges or costs
of installation or any liability for direct, indirect, or consequential damages or delay. Seller does not represent that its
product may not be compromised or circumvented; that the product will prevent any personal injury or property loss
by burglary, robbery, fire or otherwise; or that the product will in all cases provide adequate warning or protection.
Buyer understands that a properly installed and maintained alarm may only reduce the risk of burglary, robbery or fire
without warning, but is not insurance or a guaranty that such event will not occur or that there will be no personal
injury or property loss as a result thereof. Consequently seller shall have no liability for any personal injury, property
damage or loss based on a claim that the product fails to give warning. However, if seller is held liable, whether directly
or indirectly, for any loss or damage arising under this limited warranty or otherwise, regardless of cause or origin,
sellerʹs maximum liability shall not exceed the purchase price of the product, which shall be complete and exclusive
remedy against seller. No employee or representative of Seller is authorized to change this warranty in any way or grant
any other warranty.
WARNING: This product should be tested at least once a week.
Contacting RISCO Group
RISCO Group is committed to customer service and product support. You can contact us through our website
www.riscogroup.com or as follows:
United Kingdom
Tel: +44‐161‐655‐5500
[email protected]
USA
Tel: +1‐631‐719‐4400
support‐[email protected]
France
Tel: +33‐164‐73‐28‐50
support‐[email protected]
Israel
Tel: +972‐3‐963‐7777
[email protected]
Italy
Tel: +39‐02‐66590054
[email protected]
Brazil
Tel: +1‐866‐969‐5111
support‐[email protected]
China
Tel: +86‐21‐52‐39‐0066
support‐[email protected]
Belgium
Tel: +32‐2522‐7622
support‐[email protected]
Spain
Tel: +34‐91‐490‐2133
support‐[email protected]
Poland
Tel: +48‐22‐500‐28‐40
support‐[email protected]
All rights reserved.
No part of this document may be reproduced in any form without prior written permission from the publisher.
© RISCO Group 09/09 5IN1310