Crivit 1-LD3322 User Manual

Page 14



- 79 -

When the alarm sounds, press SET, SEL or MODE to stop the alarm.

Snooze feature

Snooze feature

Snooze feature
If no button is pressed when the alarm sounds, the alarm will shut off after 30
seconds and the symbol

will blink on the display. The alarm will stop and will

resume after sounding after 2 minutes. The process will repeat itself 5 times.

Timer (max. 23:59:00)

TIMER

COMPTE

TIMER

Press and hold SET for 3 seconds to enter setting mode.
The minutes of the timer time will blink on the display.
Press SEL to set minutes of the timer time and confirm your setting by pressing SET.
Set the hours in the same way.
Now the additional settings for the timer will follow. Press SEL to select the desired
mode:

Cd r

After reaching 0:00 the timer will count the set time again.

Cd U

After reaching 0:00 the timer will count forward

Cd S

After reaching 0:00 the timer will stop

Exit setting mode by pressing MODE.
The timer can be started or stopped by pressing SET.
Press and hold SET to reset the timer.
After the timer time is up an alarm will sound.

Stop watch

CHRONO

ST-UHR

CHRONO

CRONO

Press SET to start or stop the stop watch. Press SEL while the stop watch is running
to record a lap time. Up to 99 laps can be recorded.
Press and hold SET to reset the stop watch.



- 80 -

Memory feature

DATA

RECALL

ANSICHT

DATEN

APPEL

DONNEES

RECUP
DATOS

Press SEL while the stop watch is stopped to display the fastest lap on the display.
Press SET to display the other lap times.

Please note: The memory feature can only be used if at least one lap time was
recorded.

Heart rate measurement

HRM

PULS

PULSO

The subfeatures of the heart rate measurement can only be used when the chest
belt is connected.

Press SEL to access the subfeatures of the heart rate watch.

Timer

Timer

TIMER

COMPTE

TEMPORIZADOR

memory feature

MEMORY

SPEICHER

MEMOIRE

MEMORIA

target heart rate

ZONE

BEREICH

ZONE

ZONA

calories, fat burn and BMI

CALORIE

KALORIEN

CALORIES

CALORIAS

fitness

FITNESS

LEVEL

FITNESS

LEVEL

NIV FORM

PHYSIQ

NIVEL

FIT

In the middle row of the display the heart rate is shown while wearing the chest
belt. If the signal is received from the chest belt the heart symbol will flash. To the



- 81 -

right of the heart rate the heart rate in percent of the maximum heart rate is shown.
The maximum heart rate is calculated by evaluating your age, weight and height.

Warning light

ST/SP

If your heart rate reaches or exceeds
99% of your maximum heart rate, or
your heart rate exceeds the target
zone values (see target zone) the red
warning light will blink.

Timer

TIMER

COMPTE

TEMPORIZADOR

The bottom row of the display will show the elapsed training time. The middle row
will show your heart rate and the heart rate in percent of the maximum heart rate.
The timer will start automatically when the chest belt starts measuring the heart
rate. The timer will continue counting the time if the feature mode of the watch is
changed.
Press SET to select the timer mode:

TIMER

total training time

training time in heart rate target zone

▲

training time with heart rate over target zone

▼

training time with heart rate below target zone

Press and hold SET to reset the training time.



- 82 -

Memory feature

MEMORY

SPEICHER

MEMOIRE

MEMORIA

The stored values are shown in the bottom row of the display.

maximum heart rate during training

minimum heart rate during training

average heart rate during training

Press and hold SET to reset the stored values.

Target heart rate

ZONE

BEREICH

ZONE

ZONA

The bottom row of the display will show the lower and upper limit value of the
target zone.

The selected training type is shown on the top row of the display.

L- U

user defined

L-1

Health (50-65% of maximum heart rate)

L-2

Fitness (65-80% of maximum heart rate)

L-3

Performance (80-95% of maximum heart rate)

Press and hold SET for 3 seconds to enter setting mode.
Select the training type by pressing SEL. If "U" is selected (user defined) the lower
and upper limits can be set. Press SET. The display will show the lower limit.
Set the value by pressing SEL and confirm your setting by pressing SET. Set the
upper limit in the same way.



- 83 -

Exit setting mode by pressing MODE. Press and hold SEL to activate the heart rate
alarm. When the heart rate alarm is activated, the alarm symbol

will appear

on and an alarm will sound when the measured heart rate is not within the set zone
"BEEP-BEEP...BEEP-BEEP...BEEP-BEEP".
If the measured heart rate is at or above 99% of the maximum heart rate the max.
heart rate alarm will sound. "BEEP-BEEP-BEEP-BEEP-BEEP-BEEP". The max. heart
alarm is independant of the training zone and the heart rate alarm of the training
zone.

Calories, fat burn and BMI

CALORIE

KALORIEN

CALORIES

CALORIAS

The lower row will show the burned calories

CALORIE

KALORIEN

CALORIES

CALORIAS

Press SET to switch to the display of fat burn in gram

FAT BURN

FETT

CONSGRAISSES

GRASA

or to the display of your BMI

BMI

IMC

In the display for calorie burn or fat burn the values can be reset by pressing and
holding SET.

Note: To increase the accuracy of the calorie and fat burn displays your age and
weight must be set correctly.

Note: The counter for fat burn is only activated while your heart rate is above 120
beats per minute.

Notes on the BMI

Notes on the BMI

Notes on the BMI
The BMI is a statistical measurement that can be used to judge a persons weight.
For adults, a value between 18.5 and 25 is considered normal. Values below



- 84 -

18.5 are considered "underweight". Values above 25 are considered
"overweight". Values above 30 are considered "Obese".
The BMI is only a coarse guideline because it does not take a persons body type
and body composition into consideration.

Fitness

FITNESS

LEVEL

FITNESS

LEVEL

NIV FORM

PHYSIQ

NIVEL

FIT

After your training, immediately press SET. A 5 minute countdown will start (cool
down phase).
The bar will show the remaining time. On the left side of the display the heart rate
at the beginning of cool down is shown. On the right side of the display the current
heart rate is shown. The countdown time is shown on the bottom row of the
display.
After 5 minutes your fitness level will appear.

Fitness level

Heart rate

>130

130-120

120-110

110-105

105-100

<100

Coded transmission

The chest belt's transmissions are digitally coded to prevent interference if you are
training with a training partner who is using an identical watch and chest belt.
When using the chest belt for the first time, a random channel is selected
automatically. The channel is briefly displayed at the top of the display upon
entering the heart rate display mode. The available channels are CH10, CH11,
CH12, CH13 and CH14.