Kichler 43361 User Manual
We’re here to help

MOUNTING STRAP
ABRAZADERA DE MONTAJE
1) Fit shade in between frame of fixture.
2) Pass hole in top of shade over socket.
3) Raise shade up and set brackets on insides of shade on top
of brackets attached to fixture body.
4) Align holes in brackets on shade with holes in brackets of
fixture body.
5) Thread ball studs down through holes in brackets on shade
and into holes in brackets of fixture body. Tighten ball studs
to secure shade in place.
6) Adjust the length of the cables to achieve the desired height
of the mounted fixture. (See cable adjustment detail)
To raise fixture: Push cable up into canopy. Release cable
and cable will lock into place.
To lower fixture: Push button in on cable adjuster and pull
cable down. Release button to lock cable in place.
NOTE: With button pushed in cable will raise and lower.
Without button pushed in cable will only raise up and lock in
place.
7) Slip center cord from fixture through hole in short tube on
center of canopy. Match length of center cord with length of
cables. Thread set screw through hole on side of center
tube. Tighten set screw to secure center cord.
8) TURN OFF POWER.
IMPORTANT: Before you start, NEVER attempt any work
without shutting off the electricity until the work is done.
a) Go to the main fuse, or circuit breaker, box in your
home. Place the main power switch in the “OFF” position.
b) Unscrew the fuse(s), or switch “OFF” the circuit breaker
switch(s), that control the power to the fixture or room
that you are working on.
c) Place the wall switch in the “OFF” position. If the fixture
to be replaced has a switch or pull chain, place those in
the “OFF” position.
9) Find the appropriate threaded holes on mounting strap.
Assemble mounting screws into threaded holes.
10) Attach mounting strap to outlet box. (Screws provided).
Mounting strap can be adjusted to suit position of fixture.
11) Grounding instructions: (See Illus. A or B).
A) On fixtures where mounting strap is provided with a
hole and two raised dimples. Wrap ground wire from
outlet box around green ground screw, and thread into hole.
B) On fixtures where a cupped washer is provided. Attach
ground wire from outlet box under cupped washer and
green ground screw, and thread into mounting strap.
If fixture is provided with ground wire. Connect fixture
ground wire to outlet box ground wire with wire connector.
(Not provided.) After following the above steps. Never
connect ground wire to black or white power supply wires.
12) Make wire connections (connectors not provided.) Reference
chart below for correct connections and wire accordingly.
13) Push fixture to ceiling, carefully passing mounting screws
through holes in canopy.
14) Thread knurl knobs onto mounting screws. Tighten knurl
knobs to secure fixture to ceiling.
GREEN GROUND
SCREW
CUPPED
WASHER
A
B
OUTLET BOX
GROUND
FIXTURE
GROUND
DIMPLES
WIRE CONNECTOR
(NOT PROVIDED)
OUTLET BOX
GROUND
GREEN GROUND
SCREW
FIXTURE
GROUND
Connect Black or
Red Supply Wire to:
Connect
White Supply Wire to:
Black
White
*Parallel cord (round & smooth)
*Parallel cord (square & ridged)
Clear, Brown, Gold or Black
without tracer
Clear, Brown, Gold or Black
with tracer
Insulated wire (other than green)
with copper conductor
Insulated wire (other than green)
with silver conductor
*Note: When parallel wires (SPT I & SPT II)
are used. The neutral wire is square shaped
or ridged and the other wire will be round in
shape or smooth (see illus.)
Neutral Wire
Date Issued: 9/27/13
IS-43361-US
CANOPY
ESCUDETE
KNURL KNOB
PERILLA
ESTRADA
DIFFUSER
DIFUSOR
SEE OTHER SIDE FOR SPANISH TRANSLATIONS.
VEA EL OTRO LADO DE TRADUCCIONES AL ESPAÑOL.
SHADE
PANTALLA
FRAME
MARCO
15) Insert recommended bulb.
16) Raise diffuser up to fixture. Align holes in diffuser with holes
in bracket on bottom of shade.
17) Thread ball studs up through holes in diffuser and into holes
in bracket on bottom of shade. Tighten ball studs to secure
shade in place.
NOTE: Adjust position of the fixture after installation for leveling
purposes of one inch or less. (See cable adjustment detail)
BALL STUD
ESPÁRRAGO
DE CABEZA
ESFÉRICA
PRESSED
CABLE ADJUSMENT DETAIL
EL DETALLE DE AJUSTE DEL CABLE
NOT
PRESSED
UP & DOWN
UP ONLY
CABLE
CABLE
SET SCREW
TORNILLO DE
FIJACIÓN
SHORT TUBE
TUBO CORTO
CENTER
CORD
CORDÓN
DEL CENTRO
We’re here to help
866-558-5706
Hrs: M-F 9am to 5pm EST
FINIAL
CAPUCHON
SHADE
PANTALLA
FRAME
MARCO
SIDE VIEW
VISTA LATERAL