Kichler 42029 - Manual

IMPORTANT SAFETY INSTRUCTIONS
LIGHTED BULB IS HOT!
WARNING: To reduce the risk of FIRE or INJURY TO PERSON:
• Turn off and allow to cool before replacing bulb.
• Bulb gets HOT QUICKLY! Contact switch only when turning off.
• DO NOT remain in light if skin feels warm. (Light is intense,
may cause “sunburn”)
• DO NOT look directly at lighted bulb.
• Keep materials away from bulb that may burn.
• Use ONLY with wattage specified or lower.
• DO NOT touch bulb at any time, use a soft cloth. Oil from skin
may damage bulb.
• DO NOT operate fixture with missing or damaged glass.
1) Screw center column onto coupling on top of fixture body.
2) TURN OFF POWER.
IMPORTANT: Before you start, NEVER attempt any work
without shutting off the electricity until the work is done.
a) Go to the main fuse, or circuit breaker, box in your
home. Place the main power switch in the “OFF” position.
b) Unscrew the fuse(s), or switch “OFF” the circuit breaker
switch(s), that control the power to the fixture or room
that you are working on.
c) Place the wall switch in the “OFF” position. If the fixture
to be replaced has a switch or pull chain, place those in
the “OFF” position.
3) Assemble mounting screws into threaded holes in mounting
strap.
4) Attach mounting strap to outlet box. (Screws not provided).
5) Weave electrical wire and ground wire through chain links no
more than 3 inches apart. then through loop and into
canopy.
6) Grounding instructions: (See Illus. A or B).
A) On fixtures where mounting strap is provided with a
hole and two raised dimples. Wrap ground wire from
outlet box around green ground screw, and thread into hole.
B) On fixtures where a cupped washer is provided. Attach
ground wire from outlet box under cupped washer and
green ground screw, and thread into mounting strap.
If fixture is provided with ground wire. Connect fixture
ground wire to outlet box ground wire with wire connector
(not provided.) after following the above steps. Never
connect ground wire to black or white power supply wires.
7) Make wire connections (connectors not provided). Reference
chart below for correct connections and wire accordingly.
8) Push fixture to ceiling, carefully passing mounting screws
through holes in canopy.
9) Secure fixture to ceiling with threaded balls.
10) Set glass diffuser down over socket and screw socket
ring onto socket.
11) Insert recommended bulb. CAUTION: DO NOT touch bulb
with bare hands. If this happens, clean bulb with denatured
alcohol and a lint free cloth.
12) Slip glass sleeve over bulb.
13) Set shade down onto glass diffuser.
GREEN GROUND
SCREW
CUPPED
WASHER
A B
OUTLET BOX
GROUND
FIXTURE
GROUND
DIMPLES
WIRE CONNECTOR
(NOT PROVIDED)
OUTLET BOX
GROUND
GREEN GROUND
SCREW
FIXTURE
GROUND
Connect Black or
Red Supply Wire to:
Connect
White Supply Wire to:
Black White
*Parallel cord (round & smooth) *Parallel cord (square & ridged)
Clear, Brown, Gold or Black
without tracer
Clear, Brown, Gold or Black
with tracer
Insulated wire (other than green)
with copper conductor
Insulated wire (other than green)
with silver conductor
*Note: When parallel wires (SPT I & SPT II)
are used. The neutral wire is square shaped
or ridged and the other wire will be round in
shape or smooth (see illus.)
Neutral Wire
Date Issued: 1/04/13 IS-42029-US
MOUNTING STRAP
ABRAZADERA DE MONTAJE
CANOPY
ESCUDETE
THREADED BALL
BOLA ROSCADA
SHADE
PANTALLA
SOCKET RING
ANILLO DEL
CASQUILLO
GLASS DIFFUSER
DIFUSOR DE
VIDRIO
FIXTURE BODY
CUERPO DEL ARTEFACTO
CENTER COLLUMN
COLUMNA CENTRAL
BULB
BOMBILLA
GLASS SLEEVE
CAMISA DE VIDRIO