Kichler 43373 - Manual

24) Raise shade up to fixture. Fit shade inside cage on fixture.
Align holes in bracket on shade with holes in bracket on
inside of cage.
25) Thread screws down from holes in bracket on cage and
down into holes in bracket on shade.
26) From inside shade, thread ball knobs onto ends of screws.
Tighten ball knobs to secure shade in place.
27) Raise diffuser up to fixture. Pass hole in diffuser over end of
threaded pipe.
28) Pass hole in bottom trim over end of threaded pipe.
29) Thread finial onto end of threaded pipe. Tighten finial to
secure shade in place. (DO NOT over tighten.)
SEMI-FLUSH INSTALLATION
1) Pass fixture wire through long threaded pipe.
2) Screw end of long threaded pipe with hexnut into coupling
on top of fixture body.
3) Pass fixture wire through tube. Lower tube down over
threaded pipe.
4) Pass fixture wire through hole in check ring. Pass hole in
check ring over end of threaded pipe. Set check ring on top
of tube.
5) Pass hole in canopy over threaded pipe on top of fixture
body. Set canopy down onto top of tube.
6) Slip lockwasher over threaded pipe protruding from inside of
canopy and screw hexnut onto threaded pipe.
7) Follow steps 13-29 in Stem Drop Installation Instructions.
STEM DROP INSTALLATION
1) Pass fixture wire through long threaded pipe.
2) Screw end of long threaded pipe with hexnut into coupling
on top of fixture body.
3) Pass fixture wire through tube. Lower tube down over
threaded pipe.
4) Pass fixture wire through hole in check ring. Pass hole in
check ring over end of threaded pipe. Set check ring on top
of tube.
5) Pass fixture wire through coupling. Screw coupling onto end
of threaded pipe.
6) Pass wire through stem and screw stem to coupling on top
of fixture body. NOTE: Thread locking compound must be
applied to all stem threads as noted with symbol (3) to prevent
accidental rotation of fixture during cleaning, relamping, etc.
7) Pass wire through remaining stems and screw stems
together.
8) Thread one small threaded pipe into end of each small loop.
9) Attach small loop to end of last stem.
10) Pass threaded pipe at end of second small loop through
hole in canopy.
11) Slip lockwasher over threaded pipe protruding from inside of
canopy and screw hexnut onto threaded pipe.
12) Attach chain link to small loop at end of stem and to loop on
canopy.
13) TURN OFF POWER.
IMPORTANT: Before you start, NEVER attempt any work
without shutting off the electricity until the work is done.
a) Go to the main fuse, or circuit breaker, box in your
home. Place the main power switch in the “OFF” position.
b) Unscrew the fuse(s), or switch “OFF” the circuit breaker
switch(s), that control the power to the fixture or room
that you are working on.
c) Place the wall switch in the “OFF” position. If the fixture
to be replaced has a switch or pull chain, place those in
the “OFF” position.
14) Find the appropriate threaded holes on mounting strap.
Assemble mounting screws into threaded holes.
15) Attach mounting strap to outlet box. (Screws not provided)
Mounting strap can be adjusted to suit position of fixture.
16) Grounding instructions: (See Illus. A or B).
A) On fixtures where mounting strap is provided with a
hole and two raised dimples. Wrap ground wire from
outlet box around green ground screw, and thread into hole.
B) On fixtures where a cupped washer is provided. Attach
ground wire from outlet box under cupped washer and
green ground screw, and thread into mounting strap.
If fixture is provided with ground wire. Connect fixture
ground wire to outlet box ground wire with wire connector.
(Not provided.) After following the above steps. Never connect
ground wire to black or white power supply wires.
17) Make wire connections (connectors not provided.) Reference
chart below for correct connections and wire accordingly.
18) Push fixture to ceiling, carefully passing mounting screws
through holes in canopy.
19) Thread threaded balls onto mounting screws. Tighten
threaded balls to secure fixture to ceiling.
20) Insert recommended bulbs.
21) Screw short end of threaded pipe with hexnut into bottom of
fixture body.
22) Thread hexnut onto other end of threaded pipe.
23) Slip flat washer then rubber washer over end of threaded pipe.
GREEN GROUND
SCREW
CUPPED
WASHER
A B
OUTLET BOX
GROUND
FIXTURE
GROUND
DIMPLES
WIRE CONNECTOR
(NOT PROVIDED)
OUTLET BOX
GROUND
GREEN GROUND
SCREW
FIXTURE
GROUND
Connect Black or
Red Supply Wire to:
Connect
White Supply Wire to:
Black White
*Parallel cord (round & smooth) *Parallel cord (square & ridged)
Clear, Brown, Gold or Black
without tracer
Clear, Brown, Gold or Black
with tracer
Insulated wire (other than green)
with copper conductor
Insulated wire (other than green)
with silver conductor
*Note: When parallel wires (SPT I & SPT II)
are used. The neutral wire is square shaped
or ridged and the other wire will be round in
shape or smooth (see illus.)
Neutral Wire
Date Issued: 8/23/13 IS-43373-US
SEE OTHER SIDE FOR SPANISH TRANSLATIONS.
VEA EL OTRO LADO DE TRADUCCIONES AL ESPAÑOL.
COUPLING
ACOPLAMIENTO
MOUNTING STRAP
PLANCHA PARA MONTAR
CAGE
JAULA
THREADED BALL
BOLA ROSCADA
CANOPY
CAPUCHÓN
FINIAL
CAPUCHON
STEM
VÁSTAGO
3
3
LOOP
ANILLO
CHAIN LINK
ESLABÓN DE CADENA
HEXNUT
TUERCA HEXAGONAL
LOCKWASHER
ARANDELA DE
SEGURIDAD
CHECK RING
ANILLO DEL SEGURIDAD
TUBE
TUBO
LONG THREADED PIPE
TUBO ROSCADA LARGO
THREADED PIPE
TUBO ROSCADA FLAT WASHER
ARANDELA PLANA
RUBBER WASHER
ARANDELA DE
CAUCHO
SHADE
PANTALLA DIFFUSER
DIFUSOR
RUBBER WASHER
ARANDELA DE CAUCHO
FLAT WASHER
ARANDELA PLANA
HEXNUT
TUERCA HEXAGONAL
BOTTOM TRIM
GUARNICIÓN INFERIOR
HEXNUT
TUERCA HEXAGONAL
CHECK RING
ARANDELA DE
SEGURIDAD
TUBE
TUBO
BALL KNOB
PERILLA REDONDA
SCREW
TORNILLO
STEM DROP INSTALLATION
INSTALACIÓN DE GATO DE VÁSTAGO
SEMI-FLUSH INSTALLATION
LA INSTALACIÓN EN EL TECHO