Kichler 43641 User Manual
We’re here to help

CHAIN DROP INSTALLATION INSTRUCTIONS
1) Pass threaded pipe on end of small loop up through hole in
canopy.
2) Thread lockwasher onto end of threaded pipe protruding
from inside canopy.
3) Thread hexnut onto end of threaded pipe protruding from
inside canopy. Tighten hexnut to secure small loop to canopy.
4) Pass fixture wire from top of fixture through hole in bottom
of large loop. Thread large loop onto threaded pipe on top of
fixture.
5) Attach one end of chain to large loop on top of fixture.
Attach other end of chain to small loop on canopy.
6) Weave fixture wires through chain links no more than 3
inches apart.
7) Pass fixture wires through hole in small loop on canopy and
up through hole in canopy.
8) TURN OFF POWER.
IMPORTANT: Before you start, NEVER attempt any work
without shutting off the electricity until the work is done.
a) Go to the main fuse, or circuit breaker, box in your
home. Place the main power switch in the “OFF”
position.
b) Unscrew the fuse(s), or switch “OFF” the circuit breaker
switch(s), that control the power to the fixture or room
that you are working on.
c) Place the wall switch in the “OFF” position. If the fixture
to be replaced has a switch or pull chain, place those in
the “OFF” position.
9) Find the appropriate threaded holes on mounting strap.
Assemble mounting screws into threaded holes.
10) Attach mounting strap to outlet box. (Screws not provided).
Mounting strap can be adjusted to suit position of fixture.
11) Grounding instructions: (See Illus. A or B).
A) On fixtures where mounting strap is provided with a
hole and two raised dimples. Wrap ground wire from
outlet box around green ground screw, and thread into
hole.
B) On fixtures where a cupped washer is provided. Attach
ground wire from outlet box under cupped washer and
green ground screw, and thread into mounting strap.
If fixture is provided with ground wire. Connect fixture
ground wire to outlet box ground wire with wire connector
(not provided.) after following the above steps. Never
connect ground wire to black or white power supply wires.
12) Make wire connections (connectors not provided). Reference
chart below for correct connections and wire accordingly.
13) Push fixture to ceiling, carefully passing mounting screws
through holes in canopy.
14) Thread knurl knobs onto mounting screws. Tighten knurl
knobs to secure fixture to ceiling.
15) Thread end of threaded pipe with bead into hole in bottom
of socket cluster.
16) Pass hole in flat washer over end of threaded pipe. Pass
hole in rubber washer over end of threaded pipe.
17) Raise glass up to fixture. Pass hole in glass over end of
threaded pipe.
18) Pass hole in rubber washer over end of threaded pipe
protruding from bottom of glass. Pass hole in flat washer
over end of threaded pipe. (DO NOT over tighten.)
MOUNTING STRAP
ABRAZADERA DE MONTAJE
LARGE CANOPY
ESCUDETE GRANDE
Date Issued: 8/29/14
IS-43641-US
GREEN GROUND
SCREW
CUPPED
WASHER
A
B
OUTLET BOX
GROUND
FIXTURE
GROUND
DIMPLES
WIRE CONNECTOR
(NOT PROVIDED)
OUTLET BOX
GROUND
GREEN GROUND
SCREW
FIXTURE
GROUND
SEE OTHER SIDE FOR SPANISH TRANSLATIONS.
VEA EL OTRO LADO DE TRADUCCIONES AL ESPAÑOL.
KNURL KNOB
PERILLA ESTRADA
SMALL LOOP
ANILLO PEQUEÑA
CHAIN
CADENA
We’re here to help
866-558-5706
Hrs: M-F 9am to 5pm EST
LOCKWASHER
ARANDELA DE SEGURIDAD
Connect Black or
Red Supply Wire to:
Connect
White Supply Wire to:
Black
White
*Parallel cord (round & smooth)
*Parallel cord (square & ridged)
Clear, Brown, Gold or Black
without tracer
Clear, Brown, Gold or Black
with tracer
Insulated wire (other than green)
with copper conductor
Insulated wire (other than green)
with silver conductor
*Note: When parallel wires (SPT I & SPT II)
are used. The neutral wire is square shaped
or ridged and the other wire will be round in
shape or smooth (see illus.)
Neutral Wire
HEXNUT
TUERCA HEXAGONAL
19) Thread hexnut onto end of threaded pipe.
20) Pass hole in bottom trim over end of threaded pipe.
21) Thread finial onto end of threaded pipe. (DO NOT over
tighten.)
SEMI FLUSH INSTALLATION INSTRUCTIONS
1) Remove small canopy from top of fixture by unscrewing
hexnut from threaded pipe inside small canopy. Remove
hexnut and unscrew lockwasher from threaded pipe. Raise
canopy up and remove from fixture.
2) Take the large canopy with two small holes and one large
center hole. Pass fixture wire from top of fixture body through
center hole in canopy. Pass center hole in canopy down over
end of threaded pipe on top of fixture.
3) Pass fixture wire through hole in lockwasher. Thread
lockwasher onto threaded pipe protruding from inside
canopy.
4) Pass fixture wire through hole in hexnut. Thread hexnut onto
threaded pipe protruding from inside canopy.
5) Follow steps 8-21 in Chain Drop Installation Instructions.
SOCKET CLUSTER
GRUPO DEL PORTALÁMPARAS
THREADED PIPE
TUBO ROSCADA
FLAT WASHER
ARANDELA PLANA
RUBBER WASHER
ARANDELA DE CAUCHO
FINIAL
CAPUCHON
GLASS
VIDRIO
SEMI FLUSH INSTALLATION
INSTALACIÓN A SEMIRRÁS
CHAIN DROP INSTALLATION
INSTALACIÓN DEL ADORNO COLGANTE DE CADENA
KNURL KNOB
PERILLA ESTRADA
LARGE LOOP
ANILLO GRANDE
BEAD
AISLADOR
FLAT WASHER
ARANDELA PLANA
RUBBER WASHER
ARANDELA DE CAUCHO
HEXNUT
TUERCA HEXAGONAL
BOTTOM TRIM
ADORNO INFERIOR
HEXNUT
TUERCA HEXAGONAL
SMALL CANOPY
ESCUDETE PEQUEÑO
LARGE CANOPY
ESCUDETE GRANDE
MOUNTING STRAP
ABRAZADERA DE MONTAJE
LOCKWASHER
ARANDELA DE SEGURIDAD
HEXNUT
TUERCA HEXAGONAL