Kichler 43360 User Manual
We’re here to help

MOUNTING STRAP
ABRAZADERA DE MONTAJE
1) Adjust the length of the cables to achieve the desired height
of the mounted fixture. (See cable adjustment detail)
To raise fixture: Push cable up into canopy. Release cable
and cable will lock into place.
To lower fixture: Push button in on cable adjuster and pull
cable down. Release button to lock cable in place.
NOTE: With button pushed in cable will raise and lower.
Without button pushed in cable will only raise up and lock in
place.
2) Slip center cord from fixture through hole in short tube on
center of canopy. Match length of center cord with length of
cables. Thread set screw through hole on side of center
tube. Tighten set screw to secure center cord.
3) TURN OFF POWER.
IMPORTANT: Before you start, NEVER attempt any work
without shutting off the electricity until the work is done.
a) Go to the main fuse, or circuit breaker, box in your
home. Place the main power switch in the “OFF” position.
b) Unscrew the fuse(s), or switch “OFF” the circuit breaker
switch(s), that control the power to the fixture or room
that you are working on.
c) Place the wall switch in the “OFF” position. If the fixture
to be replaced has a switch or pull chain, place those in
the “OFF” position.
4) Find the appropriate threaded holes on mounting strap.
Assemble mounting screws into threaded holes.
5) Attach mounting strap to outlet box. (Screws provided).
Mounting strap can be adjusted to suit position of fixture.
6) Grounding instructions: (See Illus. A or B).
A) On fixtures where mounting strap is provided with a
hole and two raised dimples. Wrap ground wire from
outlet box around green ground screw, and thread into hole.
B) On fixtures where a cupped washer is provided. Attach
ground wire from outlet box under cupped washer and
green ground screw, and thread into mounting strap.
If fixture is provided with ground wire. Connect fixture
ground wire to outlet box ground wire with wire connector.
(Not provided.) After following the above steps. Never
connect ground wire to black or white power supply wires.
GREEN GROUND
SCREW
CUPPED
WASHER
A
B
OUTLET BOX
GROUND
FIXTURE
GROUND
DIMPLES
WIRE CONNECTOR
(NOT PROVIDED)
OUTLET BOX
GROUND
GREEN GROUND
SCREW
FIXTURE
GROUND
Connect Black or
Red Supply Wire to:
Connect
White Supply Wire to:
Black
White
*Parallel cord (round & smooth)
*Parallel cord (square & ridged)
Clear, Brown, Gold or Black
without tracer
Clear, Brown, Gold or Black
with tracer
Insulated wire (other than green)
with copper conductor
Insulated wire (other than green)
with silver conductor
*Note: When parallel wires (SPT I & SPT II)
are used. The neutral wire is square shaped
or ridged and the other wire will be round in
shape or smooth (see illus.)
Neutral Wire
Date Issued: 9/27/13
IS-43360-US
CANOPY
ESCUDETE
KNURL KNOB
PERILLA ESTRADA
THREADED PIPE
TUBO ROSCADO
BOTTOM TRIM
GUARNICIÓN INFERIOR
FINIAL
CAPUCHON
HEXNUT
TUERCA HEXAGONAL
RUBBER WASHER
ARANDELA DE CAUCHO
FLAT WASHER
ARANDELA PLANA
DIFFUSER
DIFUSOR
SEE OTHER SIDE FOR SPANISH TRANSLATIONS.
VEA EL OTRO LADO DE TRADUCCIONES AL ESPAÑOL.
SHADE
PANTALLA
CAGE
JAULA
7) Make wire connections (connectors not provided.) Reference
chart below for correct connections and wire accordingly.
8) Push fixture to ceiling, carefully passing mounting screws
through holes in canopy.
9) Thread knurl knobs onto mounting screws. Tighten knurl
knobs to secure fixture to ceiling.
10) Raise shade up to fixture. Fit shade inside cage on fixture.
Align holes in bracket on shade with holes in bracket on
inside of cage.
11) From inside shade, thread ball studs up through holes in
bracket and into holes in cage. Tighten ball studs to secure
shade in place.
12) Insert recommended bulbs.
13) Thread end of threaded pipe with hexnut into coupling in
center of socket cluster.
14) Slip flat washer then rubber washer over end of threaded pipe.
15) Raise diffuser up to fixture. Pass holes in diffuser over end
of threaded pipe.
16) Thread hexnut onto end of threaded pipe. Tighten hexnut to
secure diffuser in place. (DO NOT over tighten.)
17) Pass hole in bottom trim over end of threaded pipe.
18) Thread finial onto end of threaded pipe. (DO NOT over tighten.)
NOTE: Adjust position of the fixture after installation for leveling
purposes of one inch or less. (See cable adjustment detail)
BALL STUD
ESPÁRRAGO DE
CABEZA ESFÉRICA
PRESSED
CABLE ADJUSMENT DETAIL
EL DETALLE DE AJUSTE DEL CABLE
NOT
PRESSED
UP & DOWN
UP ONLY
CABLE
CABLE
SET SCREW
TORNILLO DE
FIJACIÓN
SHORT TUBE
TUBO CORTO
CENTER CORD
CORDÓN DEL CENTRO
We’re here to help
866-558-5706
Hrs: M-F 9am to 5pm EST