Kichler 43186 User Manual

Kichler Lighting

1) Pass wire from fixture through stems and screw stems into

couplings on top of fixture body.

NOTE: Thread locking compound must be applied to all stem

threads as noted with symbol (3) to prevent accidental

rotation of fixture during cleaning, relamping, etc.

2) Pass fixture wire through remaining stems and screw stems
together.
3) The canopy has one set of loop/chain link/loop pre-installed.

Starting with that loop/chain link/loop, pass fixture wire

through the threaded pipe on the first small loop. Next pass

the fixture wire through the hole in the small loop attached to

canopy and through the hole in the canopy.

4) With the set of loop/chain link/loop not pre-installed, from the

second set of stems, pass the fixture wire through the hole in

the threaded pipe on the end of one small loop. Thread that

small loop to the end of the last stem.

5) Pass fixture wire through hole in second small loop. Pass

fixture wire through hole in canopy. Pass threaded pipe at end

of second loop through hole in canopy. Thread wing nut onto

end of threaded pipe. Tighten wing nut to secure loop to canopy.

6) TURN OFF POWER.

IMPORTANT: Before you start, NEVER attempt any work

without shutting off the electricity until the work is done.

a) Go to the main fuse, or circuit breaker, box in your home.

Place the main power switch in the “OFF” position.

b) Unscrew the fuse(s), or switch “OFF” the circuit breaker

switch(s), that control the power to the fixture or room that

you are working on.

c) Place the wall switch in the “OFF” position. If the fixture to

be replaced has a switch or pull chain, place those in the

“OFF”

position.

7) Thread hexnut onto threaded pipe so that 5 threads are

exposed above hexnut. Thread that end of threaded pipe

into mounting strap and tighten hexnut against mounting strap.

8) Run another hexnut down threaded pipe almost touching

first hexnut. Now screw threaded pipe into mounting strap.

Mounting strap must be positioned with extruded thread

faced into outlet box. Threaded pipe must protrude out the

back of mounting strap. Screw third hexnut onto end of

threaded pipe protruding from back of mounting strap.

9) Attach mounting strap to outlet box. (Screws not provided.)
10) Attach safety cable to slot in mounting strap.
11) Grounding instructions: (See Illus. A or B).

A) On fixtures where mounting strap is provided with a hole

and two raise dimples. Wrap ground wire from outlet box

around green ground screw, and thread into hole.

B) On fixtures where a cupped washer is provided. Put

ground wire from outlet box under cupped washer and

green ground screw and thread screw into hole in mounting

strap.

If fixture is provided with ground wire. Connect fixture ground

wire to outlet box ground wire with wire connector, (not

provided) after following the above steps. Never connect

ground wire to black or white power supply wires.

12) Make wire connections (connectors not provided.) Reference

chart below for correct connections and wire accordingly.

GREEN GROUND

SCREW

CUPPED

WASHER

OUTLET BOX

GROUND

FIXTURE

GROUND

DIMPLES

WIRE CONNECTOR

(NOT PROVIDED)

OUTLET BOX

GROUND

GREEN GROUND

SCREW

FIXTURE

GROUND

Connect Black or

Red Supply Wire to:

Connect

White Supply Wire to:

Black

White

*Parallel cord (round & smooth)

*Parallel cord (square & ridged)

Clear, Brown, Gold or Black

without tracer

Clear, Brown, Gold or Black

with tracer

Insulated wire (other than green)

with copper conductor

Insulated wire (other than green)

with silver conductor

*Note: When parallel wires (SPT I & SPT II)
are used. The neutral wire is square shaped
or ridged and the other wire will be round in
shape or smooth (see illus.)

Neutral Wire

IS-43186-US

Date Issued: 7/25/14

SEE OTHER SIDE FOR SPANISH TRANSLATIONS.
VEA EL OTRO LADO DE TRADUCCIONES AL ESPAÑOL.