Casio SE-S6000 - Manual (Page 123)

122 E
Error
code
Message Meaning Action
E001 Wrong mode Mode switch position changed before fi nalization. Return the mode switch to its original setting and fi nalize
the operation.
E003 Wrong operator Clerk button pressed before fi nalization of a registration
being performed under another clerk button.
The signed on clerk differs from the clerk performed the
tracking check registration. Press the original clerk button and fi nalize the transaction
before pressing another clerk button.
Input correct check number or assign the proper clerk
number.
E004 Error INIT/FC Initialization or unit lock clear operation in progress. Complete operation.
E005 Insuffi cient memory Memory allocation exceeds total memory capacity. Reallocate memory or expand memory (if possible).
E008 Please sign on Registration without entering a clerk number. Enter a clerk number.
E009 Enter password Operation without entering the password. Enter password.
E016 Change back to REG
mode
Two consecutive transactions attempted in the refund
mode. Switch to another mode and then back to the RF mode for
the next transaction.
E017 Enter CHK/TBL
number
Attempt made to register an item without inputting a
check number. Input a check number.
E018 Enter Table number Attempt made to register an item without inputting a table
number. Input a table number.
E019 Enter number of
customers
Finalize operation attempted without entering the number
of customer. Enter the number of customer.
E021 No DEPT Link No department linked PLU is registered. Correct the program.
E023 Stock shortage Actual stock quantity becomes less than the minimum
stock quantity. Perform stock maintenance.
E024 No stock Actual stock quantity becomes / is negative. Perform stock maintenance.
E025 Illegal scale read
or entry
Scale reading error or Manual entry for scalable item. Put item on the scale again or do not enter weight by
hand.
E026 Enter condiment/
preparation PLU
No condiment / preparation PLU is registered. Register condiment / preparation PLU.
E029 In the tender
operation
Item registration is prohibited, while partial tender. Finalize the transaction.
E030 Press RATE TAX key Finalization of a transaction attempted without register-
ing rate-tax. Register .
E031 Press ST key Finalization of a transaction attempted without confi rm-
ing the subtotal. Press .
E032 Press FSST key Finalization of a transaction attempted without confi rm-
ing of the food stamp subtotal. Press .
E033 Enter tendered
amount
Finalize operation attempted without entering amount
tender. Enter the amount tendered.
E035 Change amount
exceeds limit
Change amount exceeds preset limit. Input amount tendered again.
E036 Remove money from
the drawer
Contents of the drawer exceed programmed limit. Perform pick up operation.
E037 Digit or amount
limitation over
High amount lock out / low digit lock out error Enter correct amount.
E038 Perform money
declaration
Read / reset operation without declaring cash in drawer.
This error appears only when this function is activated. Perform money declaration.
E040 Issue guest receipt Attempt to register a new transaction without issuing a
guest receipt. Issue a guest receipt.
E041 Print validation Attempt to register a new transaction without validation. Perform validation operation.
E042 Insert VLD paper
and retry
Validation paper (slip printer) has run out. Insert new validation paper.
E044 Print Cheque Attempt to register a new transaction without printing check. Perform check print.
E045 Print Check
Endorsement
Attempt to register a new transaction without printing
check endorsement. Perform check endorsement.
E046 REG buffer full Registration buffer full. Finalize the transaction.
E047 Print bill Separate check buffer full. Allocate suffi cient separate check buffer.
E048 Insert slip paper
and retry
Attempt to register a new transaction without printing slip.
No paper is inserted or paper is out in the slip printer. Perform slip printing operation.
Insert new slip paper.
E049 CHECK memory full Check tracking index memory full. Finalize and close the check number currently used.
E050 DETAIL memory full Check tracking detail memory full. Finalize and close the check number currently used.
This section describes what to do when you have problems with operation.
Troubleshooting
When an error occurs
Errors are indicated by an error codes. When this happens, you can usually fi nd out what the problem is as illus-
trated below.
Press C and check the appropriate section of this manual for the operation you want to perform.