Invotel SX2100EZ - Manual (Page 3)

iii
Special settings:
If audio activates suddenly in Default switch setting , your lines may be
“too Hot” try this one time programming:
Confirm switch is in Default , select L1, while dial tone is being heard, wait about 8
seconds till you hear a BEEP now press then You will get continues
BEEPS and blinking audio as confirmation. Hang up and repeat for L2 if needed.
If your lines are “too weak” the Hold audio may not activate when you press
Hold button in Default setting try this one time programming to make the default
setting more responsive:
Confirm switch is in Default , select L1, while dial tone is being heard, wait about 12
seconds till you hear a double BEEP now press then You will get
continues BEEPS and blinking audio as confirmation. Hang up and repeat for L2 if
needed.
This device can be programmed to activate compatible corded phones via just Hold
button and cordless phones etc. via Flash then Hold for example: say you have ATT
952 corded phones and Uniden cordless phones, try this:
Set switch to Default , select L1, wait about 12 seconds till you hear a double
BEEP now press then You will get confirmation via continues
BEEPS and blinking audio. Hang up and repeat for L2 if applicable; Now set the
switch to ALT1
In each one of above cases the device stays in that special setting there after.
Unless you get a long power outage or you remove the phone lines from the device.
To remove special settings: UN-plug the 9VAC power for a minute or remove the
corresponding wires from Wall Jacks for 10 seconds
Warranty
This product is warranted against defects for a period of one (1) year from the date of original
invoice. We will repair/replace the Product with no charge for parts or labor within this time. To
obtain warranty service the Product needs to be returned fright prepaid by the customer with a
copy of original invoice. This warranty does not apply if in the sole opinion of Innovative
Telecommunication Technology, the product has been tampered with or damaged by lightning
or any other acts of nature, misuse, neglect or unauthorized service.
EXCEPT AS SPECIFICALLY PROVIDED IN THIS AGREEMENT, THERE ARE NO OTHER
WARRANTIES, EXPRESSED OR OTHERWISE,INCLUDING, BUT NOT LIMITED TO ANY
IMPLIED WARRANTIES OR MERCHANTIBILITES OR FITNESS FOR A SPECIAL PURPOSE.
IN NO EVENT SHALL INNOVATIVE TELECOMMUNICATION TECHNOLOGY (INVOTEL) BE
LIABLE FOR LOSS OF PROFITS OR BENEFITS, INDIRECT, SPECIAL, CONSEQUENTIAL
OR OTHERWISE ARRISING FROM ANY BREACH OF THIS WARRANTY OR OTHERWISE.
Operation in Default setting:
To place a call on Music-On-Hold, simply press the button on your
telephone, the Music will be heard on the line and the red HOLD Light indicator for
that line turns ON , to return to the call just re-select that line.
Be sure to allow 2 seconds before putting a call on HOLD.
Deactivating hold music manually If for any reason the hold music is activated
inadvertently, it can be deactivated by pressing the button
The following are examples of phones that work in ALT1 or ALT2 settings: Casio,
American Venture, ATT 962, ATT 972, Panasonic KX-TG 2000B, KX-TG4000B,
KXTG2000, KX-TG2720, KX-TG2730, KX-TG2740, KXTG4000, KX-TGA200, KXTGA400, KX-
TGA420, SBC 410
List of compatible corded phones supported via Default setting:
Please note: This is a partial list, there are other factors relevant to activation via Hold button in
Default setting-see-the trouble shooting section or special setting, If your phone is not on this
list , although you can try the default setting, use the ALT1 setting. ALT1 works on all phones.
Also note that 4 line capable phones in this list work in ALT1 setting (Flash then Hold)
If you have a 4 line capable phone with only 2 lines being used and still require activation
via just hold button then the proper adapter model is SX4400EZ
AT&T: 21070, 262, 272, 412, 422, 4952, 612, 622, 712, 722, 732, 742, 752, 812, 822, 830,
832, 842, 843, 853, 854, 874, 902, 912,922, 944, 952, 953, 954, 955, 964, 974,
SIGNATURE, FT483
Brother Quatro: 412
Bell: 223, 232, 259, 261, 268, 367, 470, 52905, Sonecor 412, 412CID, 4900, BE5200,
BE5300, Techline 420
GE: 187, 2-9315-A, 2-9318, 2-9435-A -B -C, 2-9436-A, 2-9438-A, 2-9450-A -B -C -D -E -
F, 2-9439-A to -EGL, 2-9451A, 2-9481, 2-9487GE2-A, 2-9488, 2-9638-A, 2-9975, 2-
9488GE2-A RCA 25403 RCA
IBM: 412, 412CID, 4900
Northern Telecom: Unity
Phonemate: PMG-4600
Panasonic: KX-T3110 3120 3122 3135 3145 3155 3160 3165 3170 3175 3280 3980-H
3980-R7 3981, KX-TC930, KX-TS20, KX-TS21, KX-TS25, KX-TS27, KX-TS208, VA-8400
Radio Shack: 206, 208, 209, 210, 212, 411, 412, 612, 43-373D, 43-430, 43-642, ET-180,
43-470, ET-184, ET-192, ET-193, 43-622, 43-469 , 1710, 1753
Sony: IT-M804
SBC:
2105, 4000
Southwestern Bell: FT325, FT360, FT365BL FT383, FT412, FT483, FT484
Sprint/Radio Shack: SP-702 / 43-5702, SP-705
TT Systems: 4012, 412, 412CID, 4900, 4300, 5100, 5200, 5300, 7993
Vtech: 4121
ALT2 Default ALT1
Hang up and set switch to Middle position
FLASH
FLASH
P6
HOLD
Tip: If you have audio flicker problem , Reduce the Volume
on your audio source
*
* FLASH
FLASH *
P3