Verilink QUAD DATA (880-503319-001) Product Manual - Manual (Page 17)

Quick Set-Up
Verilink QUAD DATA User Manual 2-3
6. Initially there is no password, press E NTER .
7. The SCM Main Menu appears.
8. Navigate to slot 3, the QUAD DATA module. Type “S” and press
E NTER . At the prompt type “1,3” and press E NTER .
9. Type “C” and press E NTER to access the QUAD DATA
Configuration Menu.
NOTE: For the rest of this chapter, you will not be instructed to press
E NTER after each command. Generally, E NTER is used after
each keyboard entry.
Figure 2-2 shows the default values for the QUAD DATA
Configuration Menu.
Figure 2-2 QUAD DATA Configuration Menu
Once each port has been configured, the Circuit Manager feature of
the SCM is used to build the connections to other modules.
Module
Configuration
The QUAD DATA Configuration Menu is used to enable each of the
ports and configure parameters such as interface type and data
port mode.
1. Type “I1”, the prompt Port 1 in service? (y/n): Port 1 in service? (y/n): Port 1 in service? (y/n): Port 1 in service? (y/n): appears. Type “y”
for yes.
-- QUAD DATA CONFIGURATION MENU -- -- QUAD DATA CONFIGURATION MENU -- -- QUAD DATA CONFIGURATION MENU -- -- QUAD DATA CONFIGURATION MENU --
Port 1 Port 2 Port 3 Port 4 Port 1 Port 2 Port 3 Port 4 Port 1 Port 2 Port 3 Port 4 Port 1 Port 2 Port 3 Port 4
In) in service no no no no In) in service no no no no In) in service no no no no In) in service no no no no
Fn) interface type V.35 V.35 V.35 V.35
Fn) interface type V.35 V.35 V.35 V.35 Fn) interface type V.35 V.35 V.35 V.35 Fn) interface type V.35 V.35 V.35 V.35
Mn) data port mode DCE DCE DCE DCE
Mn) data port mode DCE DCE DCE DCE Mn) data port mode DCE DCE DCE DCE Mn) data port mode DCE DCE DCE DCE
Cn) clock option ST ST ST ST
Cn) clock option ST ST ST ST Cn) clock option ST ST ST ST Cn) clock option ST ST ST ST
On) enable LOS detect no no no no
On) enable LOS detect no no no no On) enable LOS detect no no no no On) enable LOS detect no no no no
An) allow loopback no no no no
An) allow loopback no no no no An) allow loopback no no no no An) allow loopback no no no no
Ln) X.21 C/I setting --- --- --- ---
Ln) X.21 C/I setting --- --- --- --- Ln) X.21 C/I setting --- --- --- --- Ln) X.21 C/I setting --- --- --- ---
SRn) DTR/DSR setting DSR/normal DSR/normal DSR/normal DSR/normal
SRn) DTR/DSR setting DSR/normal DSR/normal DSR/normal DSR/normal SRn) DTR/DSR setting DSR/normal DSR/normal DSR/normal DSR/normal SRn) DTR/DSR setting DSR/normal DSR/normal DSR/normal DSR/normal
SSn) RTS/CTS setting CTS/normal CTS/normal CTS/normal CTS/normal
SSn) RTS/CTS setting CTS/normal CTS/normal CTS/normal CTS/normal SSn) RTS/CTS setting CTS/normal CTS/normal CTS/normal CTS/normal SSn) RTS/CTS setting CTS/normal CTS/normal CTS/normal CTS/normal
SDn) DCD/LL setting DCD/normal DCD/normal DCD/normal DCD/normal
SDn) DCD/LL setting DCD/normal DCD/normal DCD/normal DCD/normal SDn) DCD/LL setting DCD/normal DCD/normal DCD/normal DCD/normal SDn) DCD/LL setting DCD/normal DCD/normal DCD/normal DCD/normal
SMn) TM/RL setting TM /off TM /off TM /off TM /off
SMn) TM/RL setting TM /off TM /off TM /off TM /off SMn) TM/RL setting TM /off TM /off TM /off TM /off SMn) TM/RL setting TM /off TM /off TM /off TM /off
C) copy port T) timing C) copy port T) timing C) copy port T) timing C) copy port T) timing
X) exit this menu X) exit this menu X) exit this menu X) exit this menu
A [0.0.0.60] [1,3] QUAD DATA > A [0.0.0.60] [1,3] QUAD DATA > A [0.0.0.60] [1,3] QUAD DATA > A [0.0.0.60] [1,3] QUAD DATA >