beautypg.com

Thinklogical Velocitykvm-4 Quick Start Guide User Manual

Velocity kvm-4 transmitter velocity kvm-4 receiver, Vel-u00m04-scrx

background image

100-240V-,0.5A, 50/60 Hz

T 2A ,250VAC

CAUTION! Replace with same type and rating fuse.

CNTRL

LINE OUT

HOST

USB HID

U
P
D
A
T
E
S

PWR

FOL

USB 2.0

SER IAL PORT

L1

DVI OUT DDC

DVI OUT

STEP 6: A DVI-D cable (CBL000009-002MR) is

included. Connect it to the CPU DVI Video Card

and the other end to the VelocityKVM

Transmitter’s DVI IN connector.

STEP 7: (Optional) Connect your
local monitor cable (not included) to
the DVI OUT connector on the
VelocityKVM Transmitter.

UPDATES

DEV

DVI OUT

DVI IN

SER IAL PORT

L2

L1

LINE IN

MIC OUT

HID

P
S
2

P
S
2

LOCAL FROM CPU

U S B 1 .1

U S B 1 .1

USB HID

HOST

CNTRL

CAUTION! Replace with same type and rating fuse.

100-240V-,0.5A, 50/60 Hz

T 2A ,250VAC

CLINK

PWR

CP

FOL

USB 2.0

USB 2.0

Audio OUT
Audio IN

PS/2 Keyboard
PS/2 Mouse
USB HID (Kybd/Mouse)
USB 1.1 (Kybd/Mouse)

Audio IN

PS/2

Keyboard/

Mouse

USB HID

USB 1.1

DVI IN

DVI OUT

Audio OUT

Velocity

KVM-4

Transmitter

Velocity

KVM-4

Receiver

STEP 8: If desired, connect your local
keyboard and mouse by inserting the PS/2 or
USB HID connectors into the VelocityKVM
Transmitter’s local devices receptacles.

STEP 4: Connect your Multi-
Mode Fiber Optic cables
between the Transmitter and
Receiver units as shown.
(1 or 2 Single-Mode fibers can
also be used, depending on the
model and required fiber
length.)

L1: Video and Data Tx to Rx
L2: Data Rx to Tx

STEP 1: Ensure that the POWER ON/OFF switch is
in the OFF position (0) on both the Tx and Rx units.
Connect the supplied AC Power Cords to both units
and plug them into a standard AC supply. LEAVE
BOTH SWITCHES IN THE OFF POSITION.

STEP 5: Connect
your KVM devices
to the CPU using
the cables supplied
in KIT-000005-R.

STEP 3: Turn the
Receiver unit ON.

Verify that all system
features are functioning
properly. Turn on the
Source (CPU) and
Display Devices last.

STEP 2: Connect your desktop devices

(monitors, keyboard, mouse, etc.) to the

Receiver using standard cables.

PHONE:

(800) 291-3211

WEBSITE:

www.thinklogical.com

EMAIL:

[email protected]

The Thinklogical™ Velocity

kvm-4

Multi-Mode Fiber Optic System consists of a transmitter unit and a receiver unit connected by two multi-mode fiber optic

cables (or by one or two optional single-mode fibers). The transmitter unit connects to the computer with standard cables and the receiver unit provides
connections to the user interface devices. The Velocity

kvm-4

supports PS/2, full duplex stereo audio, serial (RS-232), USB 1.0 (HID) device ports and

USB 1.1. USB 2.0 (high speed up to 480Mbps) is optional.

Note: In order to

avoid possible exposure
to laser energy, it is good
practice to attach the
fiber optic cables prior to
applying power to the
unit.

Note: Be sure to

leave adequate ventilation
space on both sides of
the units (2” minimum),
especially if the units are
being stacked

CONTENTS
Upon receiving your Thinklogical™
Velocity

kvm-4

Extender you should

find the following items:

VelocityKVM Extender Transmitter
VelocityKVM Extender Receiver
2 AC power cords, PWR-000006-R

(International connections may differ.)

VelocityKVM Extender Cables:

1

DVI-D Male Cable, 2 meters, CBL000009-002MR

1 Cable Kit (8 six ft. peripheral cables.) KIT-000005-R

VelocityKVM Extender Product Manual

All physical connections to the product use industry-standard connectors.

L1

L2

L1

L2

PS/2 Connector

USB HID Connector

TM

STEP 10: Turn on the
Source (CPU) last. Verify
that all system features are
functioning properly.

Visit us online at

www.thinklogical.com

for more

product information, current updates and the
complete line of Thinklogical products.

MIC IN

Copyright c 2009. All rights reserved. Printed in the U.S.A. All trademarks and service marks are the property of their respective owners.

Multi-Mode Fiber Extension System – DVI Two Display

L2

8 Mounting bracket

screws

Single Head Single Link

Velocity

kvm-4

Fiber Optic Transmitter

2 Mounting bracket screws

in four places.

RACK-MOUNT OR DESK-TOP
OPTIONS:
Like all Thinklogical™

KVM extenders, the

Velocity

KVM-4

can be mounted in a standard EIA 19"

rack or on a shelf or desk-top.

Each mounting bracket is secured

by four screws and can be safely

removed from the transmitter or

receiver unit for desk-top mounting.

VEL-U00M04-SCRX

VEL-U00M04-SCRX

This manual is related to the following products: