Studio Technologies 5152 V.2 - Manual (Page 33)

Model 5152 User Guide Issue 4, September 2013
Studio Technologies, Inc. Page 33
Model 5152
Video Generator/Audio Embedder Module
Specifications
SDI Compatibility, Supported Formats and
Rates:
HD-SDI per SMPTE ST 292:2011:
720p: 50, 59.94, 60
1080i: 50, 59.94, 60
1080p: 23.98, 24, 25, 29.97, 30
1080psf: 23.98, 24, 25
3G-SDI Level A per SMPTE ST 424:2006 and
ST 425:2011:
1080p: 50, 59.94, 60
SD-SDI per SMPTE® ST 259:2008:
Not supported
Audio Embedding into SDI:
Per SMPTE ST 299-1-2010
Coaxial (BNC) SDI Input and Output:
Type: unbalanced
Impedance: 75 ohms
Level: 800 mV p-p, nominal
Optical Input (optional):
Compliance: SMPTE ST 297:2006 (as applicable)
Fiber Type: single mode
Wavelengths Supported: 1250 to 1650 nm
Receive Sensitivity: –17 dBm, nominal @
2.97 Gb/s
Maximum Input Power: –3 dBm, nominal
Optical Output (optional):
Compliance: SMPTE ST 297:2006 (as applicable)
Fiber Type: single mode
Wavelength: 1310 nm (FP laser) or CWDM (DFB
laser), as per order
Launch Power: –3 dBm, nominal
Typical Fiber Interconnect Length: 10 km
minimum
Digital Audio Inputs: 4 (2-channel)
Type: AES3, unbalanced, 75 ohms (formerly
AES3id)
Sample Rate Range: 32-48 kHz
Maximum Bit Depth: 24
Nominal Level: –20 dBFS or –18 dBFS
Timing: asynchronous, each input contains sample
rate conversion (SRC) circuitry
Signal Present LEDs: lights at ≥ –40 dBFS
GPI: active low, “pulled up” to 3.3 volts DC using
5 k ohm resistor; activates on closure to common
(applies to Model 5152 modules with serial num-
bers 00251 and later)
GPO: active high, 3.3 volts DC with series resis-
tance of 150 ohm; short circuit current of approxi-
mately 22 milliamperes in reference to common
(applies to Model 5152 modules with serial num-
bers 00251 and later)
Remote Control Data Interface: RS-485 115.2
Kb/s, 8-1-N; compatible with Studio Technologies’
Model 5190 Remote Access Module
Connectors:
Coaxial SDI Input and Output: BNC, 3G-SDI
optimized, gold plating on center pin, per IEC
61169-8 Annex A
Optical Module: MSA-compliant SFP
Digital Audio Input: 1, 9-pin D-subminiature
female (DE-9F); requires installer-provided DE-9M
DC Input/Data: 1, 4-position male header. Refer
to Appendix B for mating connector details.
GPI/GPO: 1, 3-position male header (applies to
modules with serial numbers 00251 and later).
Refer to Appendix B for mating connector details.
Power Requirement: 12 volts DC nominal,
400 mA max; acceptable range 10-18 volts DC,
480 mA max at 10 volts
Dimensions (Overall):
3.75 inches wide (9.5 cm)
1.69 inches high (4.3 cm)
2.30 inches deep (5.8 cm)
Mounting: requires custom implementation;
no mounting method provided. Refer to Appendix C
for details.
Weight: 0.2 pounds (91 g)
Specifications and information contained in this
User Guide subject to change without notice.