Space Ray RSTP Series - Manual (Page 15)

Form 43206000
-14- Sept 2011
KEY DIMENSIONS AND COMPONENTS OF THE GAS CONNECTIONS
END VIEW
Gas Pressure
= 2 PSIG
Gas Supply
Piping
Sediment Trap
(Drip Leg)
*Manual Gas
Shut Off Valve
*Second Stage Regulator with
Vent Leak Limiter to reduce the
Supply Pressure below 14” W.C.
* Available as Accessories
14 to 17”
(36 to 43cm)
2” (5cm) Max.
Displacement
Approved
Flexible Connector
Adaptor 1/2” NPT female
Adaptor 1/2” NPT male
Alternate Supply
Locations
SIDE VIEW
Control Box
END VIEW
INCORRECT POSITIONS
WRONG WRONG
WRONG
WRONG
US ONLY: US ONLY: US ONLY: US ONLY: CONNECTOR MUST BE INSTALLED IN “ CONNECTOR MUST BE INSTALLED IN “ CONNECTOR MUST BE INSTALLED IN “ CONNECTOR MUST BE INSTALLED IN “⊃ ⊃ ⊃ ⊃” CONFIGURATION. ” CONFIGURATION. ” CONFIGURATION. ” CONFIGURATION.
USE ONLY THE 36” LONG CONNECTOR THAT WAS FURNISHED WITH USE ONLY THE 36” LONG CONNECTOR THAT WAS FURNISHED WITH USE ONLY THE 36” LONG CONNECTOR THAT WAS FURNISHED WITH USE ONLY THE 36” LONG CONNECTOR THAT WAS FURNISHED WITH
THIS HEATER.
THIS HEATER. THIS HEATER. THIS HEATER.
US ONLY: A gas connector certified for use on a tubular type A gas connector certified for use on a tubular type A gas connector certified for use on a tubular type A gas connector certified for use on a tubular type infrared heater per the standard for Connectors infrared heater per the standard for Connectors infrared heater per the standard for Connectors infrared heater per the standard for Connectors
for Gas Appliances, ANSI Z21.24/CSA 6.10 is supplied for installation in US only. The gas connector is 36” long for Gas Appliances, ANSI Z21.24/CSA 6.10 is supplied for installation in US only. The gas connector is 36” long for Gas Appliances, ANSI Z21.24/CSA 6.10 is supplied for installation in US only. The gas connector is 36” long for Gas Appliances, ANSI Z21.24/CSA 6.10 is supplied for installation in US only. The gas connector is 36” long
and
and and and 1 1 1 1/ // /2 2 2 2” nominal ID, and must be installed as shown above, in ” nominal ID, and must be installed as shown above, in ” nominal ID, and must be installed as shown above, in ” nominal ID, and must be installed as shown above, in one plane, and without sharp bend one plane, and without sharp bend one plane, and without sharp bend one plane, and without sharp bends, kinks or s, kinks or s, kinks or s, kinks or
twists. twists. twists. twists.
CANADA ONLY: A Type I hose connector should be used that is certified as being in compliance with the A Type I hose connector should be used that is certified as being in compliance with the A Type I hose connector should be used that is certified as being in compliance with the A Type I hose connector should be used that is certified as being in compliance with the
Standard for Elastomeric Composite Hose and Hose Couplings for Conducting Propane and Natural Gas Standard for Elastomeric Composite Hose and Hose Couplings for Conducting Propane and Natural Gas Standard for Elastomeric Composite Hose and Hose Couplings for Conducting Propane and Natural Gas Standard for Elastomeric Composite Hose and Hose Couplings for Conducting Propane and Natural Gas
(CAN/CGA 8.1) and is of length of
(CAN/CGA 8.1) and is of length of (CAN/CGA 8.1) and is of length of (CAN/CGA 8.1) and is of length of 36+/ 36+/ 36+/ 36+/---- 6 in (90+/ 6 in (90+/ 6 in (90+/ 6 in (90+/---- 15 cm). 15 cm). 15 cm). 15 cm). The gas connector The gas connector The gas connector The gas connector must be installed as shown must be installed as shown must be installed as shown must be installed as shown
above above above above, in one plane, and without sharp bends, kinks or twists. , in one plane, and without sharp bends, kinks or twists. , in one plane, and without sharp bends, kinks or twists. , in one plane, and without sharp bends, kinks or twists.