Spray star 3000 hose reel parts list, Hose reel mounting instructions, Accessories – Smithco Spray Star 3000 (sn 3500 – Current) Parts & Service Manual User Manual
Page 115: Ref# part# description quantity
113
Accessories
SPRAY STAR 3000 HOSE REEL PARTS LIST
REF#
PART#
DESCRIPTION
QUANTITY
1
16-153
Elbow
3
/
4
MPT x
3
/
4
HB
1
2
16-859
Ball Valve
3
/
4
1
3
18-073
Close Nipple
3
/
4
3
6
16-151
Elbow
3
/
4
FPT x
3
/
4
HB
1
7
16-154
Barb Fitting
3
/
4
MPT x
3
/
4
HB
1
8
18-281
Black Pipe Tee
3
/
4
1
10
33-477
Hose Reel Mount
1
11
Hose Reel
1
18-249
Fitting
3
/
4
MPT x
3
/
4
HB
1
HB-38-16-175
Bolt
3
/
8
- 16 x 1
3
/
4
4
HW-38
Washer
3
/
8
8
HNTL-38-16
Lock Nut
3
/
8
- 16
4
12
33-249
Air Gap Filler Kit
(part of machine)
1
16-945
Fitting
1
13
33-192
Tank Strap
(part of machine)
2
14
HB-38-16-225
Bolt
3
/
8
- 16 x 2
1
/
4
4
HB-38-16-250
Bolt
3
/
8
- 16 x 2
1
/
2
4
HNTL-38-16
Lock Nut
3
/
8
- 16
8
HW-38
Washer
3
/
8
8
15
33-142
300 gal. Poly Tank
(part of machine)
1
16
50-081
Rubber Bumper
1
HWL-38
Lockwasher
3
/
8
1
HN-38-16
Nut
3
/
8
- 16
1
HOSE REEL MOUNTING INSTRUCTIONS
1. Wear Protective clothing when draining the tank and taking apart the lines.
2. Drain the tank and spray system in a safe and approved method insuring that no chemical or water remain
in it as you will be taking apart lines.
3. Before starting remove the key, set the park brake and block the wheels.
4. Remove the air gap filler and plug the hole from the outside with a 1" hex plug.
5. Remove the rear tank strap (Ref 13) and replace with the hose reel mount (Ref 10). Mount it with the long
side of the platform to the rear of the machine. Use the same hardware from the tank strap.
6. Put the hose reel on the hose reel bracket with the fitting on the left hand side of the machine. Line up the
slots over the holes in the legs of the hose reel bracket, put the
3
/
8
washers over the slots and the
3
/
8
- 16 x 1
3
/
4
bolts through with the
3
/
8
washers and
3
/
8
-16 locknuts on the bottom and tighten.
7. Use teflon tape and tighten all fittings as you are installing them.
8. For 3002, 3006 or 3007: Disconnect hose from elbow on (B) and disconnect (B) from (A) with reducer
bushing remaining on (B). Reassemble with the new fittings as shown in the plumbing drawing. Reconnect
hose onto elbow.
For 3004: Remove and discard hex plug from (C). Reassemble with new fittings as shown in plumbing
drawing.
9. Put the 18-249 barb fitting into the hose reel and tighten.
10. Use 8887-48 hose to connect reel to ball valve, secure with 18-040 hose clamp.
11. Use 22-075 nylon ties to tie hose to main feed hose.
NOTE: To reinstall the Air Gap Filler, see the next page.