Satel ETHM-1 - Manual (Page 4)

SATEL 2014-04-02
cmd meaning answer
0x7F list of new states of above data 0x7F + 5 bytes (each bit is set when new data is collected in corresponding command,
each bit is cleared after reading the corresponding command):
1 byte - .0 - 1 = new data in 0x00 command
.1 - 1 = new data in 0x01 command
.2 - 1 = new data in 0x02 command
.3 - 1 = new data in 0x03 command
.4 - 1 = new data in 0x04 command
.5 - 1 = new data in 0x05 command
.6 - 1 = new data in 0x06 command
.7 - 1 = new data in 0x07 command
1 byte - .0 - 1 = new data in 0x08 command
.1 - 1 = new data in 0x09 command
.2 - 1 = new data in 0x0A command
.3 - 1 = new data in 0x0B command
.4 - 1 = new data in 0x0C command
.5 - 1 = new data in 0x0D command
.6 - 1 = new data in 0x0E command
.7 - 1 = new data in 0x0F command
1 byte - .0 - 1 = new data in 0x10 command
.1 - 1 = new data in 0x11 command
.2 - 1 = new data in 0x12 command
.3 - 1 = new data in 0x13 command
.4 - 1 = new data in 0x14 command
.5 - 1 = new data in 0x15 command
.6 - 1 = new data in 0x16 command
.7 - 1 = new data in 0x17 command
1 byte - .0 - 1 = new data in 0x18 command
.1 - 1 = new data in 0x19 command
.2 - 1 = new data in 0x1A command
.3 - 1 = new data in 0x1B command
.4 - 1 = new data in 0x1C command
.5 - 1 = new data in 0x1D command
.6 - 1 = new data in 0x1E command
.7 - 1 = new data in 0x1F command
1 byte - .0 - 1 = new data in 0x20 command
.1 - 1 = new data in 0x21 command
.2 - 1 = new data in 0x22 command
.3 - 1 = new data in 0x23 command
.4 - 1 = new data in 0x24 command
.5 - 1 = new data in 0x25 command
.6 - 1 = new data in 0x26 command
.7 - 1 = new data in 0x27 command
In INT-RS v2.xx (see below):
1 byte - .0 - 1 = new data in 0x28 command
.1 - 1 = new data in 0x29 command
.2 - 1 = new data in 0x2A command
.3 - 1 = new data in 0x2B command
.4 - 1 = new data in 0x2C command
.5 - 1 = new data in 0x2D command
.6 - 1 = new data in 0x2E command
.7 - 1 = new data in 0x2F command
Note: in INT-RS v1.xx - 0x7F command returns 0x7F + 5 bytes,
in INT-RS v2.xx - 0x7F command returns 0x7F + 5 bytes, but 0x7F command send with 1 additional byte (no matter
of its value) returns 0x7F + 6 bytes (see the list above).
- 4 -