Satel ETHM-1 - Manual (Page 20)

SATEL 2014-04-02
384,0,32,'Low voltage on radio zone battery '
384,1,32,'Voltage on radio zone battery ok '
388,0, 1,'Zone trouble (masking) '
388,1, 1,'Zone ok (masking) '
400,0, 2,'Disarm '
400,1, 2,'Arm '
401,0, 2,'Disarm by user '
401,1, 2,'Arm by user '
402,0, 2,'Group disarm '
402,1, 2,'Group arm '
403,0,15,'Auto-disarm '
403,1,15,'Auto-arm '
404,0, 2,'Late disarm by user '
404,1, 2,'Late arm by user '
405,0, 2,'Deferred disarm by user '
405,1, 2,'Deferred arm by user '
406,0, 2,'Alarm cleared '
407,0, 2,'Remote disarm '
407,1, 2,'Remote arm '
408,1, 1,'Quick arm '
409,0, 1,'Disarm by zone '
409,1, 1,'Arm by zone '
411,0, 0,'Callback made '
412,0, 0,'Downloading successfully finished '
413,0, 0,'Unsuccessful remote downloading attempt '
421,0, 3,'Access denied '
421,1, 3,'Access denied '
422,0, 3,'User access '
422,1, 3,'User access '
423,0, 1,'Alarm - armed partition door opened '
441,1, 2,'Arm (STAY mode) '
442,1, 1,'Arm by zone (STAY mode) '
454,0, 2,'Arming failed '
458,0, 2,'Delay activation time started '
461,0, 1,'Alarm (3 wrong access codes) '
462,0, 3,'Guard round '
462,1, 3,'Guard round '
570,0, 1,'Zone bypass '
570,1, 1,'Zone unbypass '
571,0, 1,'Fire zone bypass '
571,1, 1,'Fire zone unbypass '
572,0, 1,'24h zone bypass '
572,1, 1,'24h zone unbypass '
573,0, 1,'Burglary zone bypass '
573,1, 1,'Burglary zone unbypass '
574,0, 1,'Group zone bypass '
574,1, 1,'Group zone unbypass '
575,0, 1,'Zone auto-bypassed (violations) '
575,1, 1,'Zone auto-unbypassed (violations) '
601,0, 6,'Manual transmission test '
602,0, 0,'Transmission test '
604,0, 2,'Fire/technical zones test '
604,1, 5,'End of fire/technical zones test '
607,0, 2,'Burglary zones test '
607,1, 5,'End of burglary zones test '
611,0, 1,'Zone test ok '
612,0, 1,'Zone not tested '
613,0, 1,'Burglary zone test ok '
614,0, 1,'Fire zone test ok '
615,0, 1,'Panic zone test ok '
621,0, 0,'Reset of event log '
622,0, 0,'Event log 50% full '
623,0, 0,'Event log 90% full '
625,0, 6,'Setting system real-time clock '
625,1, 0,'System real-time clock trouble '
627,0, 4,'Service mode started '
628,0, 4,'Service mode finished '
800,0,6 ; DO NOT TRANSLATE - TEST FUNCTION,'Key long pressed '
801,0,4 ; DO NOT TRANSLATE - TEST FUNCTION,'Settings sent - chime 1...64 ON '
802,0,4 ; DO NOT TRANSLATE - TEST FUNCTION,'Settings sent - chime 1...64 OFF '
803,0,4 ; DO NOT TRANSLATE - TEST FUNCTION,'Settings sent - chime 65..128 ON '
804,0,4 ; DO NOT TRANSLATE - TEST FUNCTION,'Settings sent - chime 65..128 OFF '
805,0,4 ; DO NOT TRANSLATE - TEST FUNCTION,'Settings sent - chime bypassed '
982,0, 6,'Change of user telephone code '
983,0, 6,'User telephone code broken '
984,0, 1,'Alarm - ABAX device tamper (no connection) '
984,1, 1,'ABAX device tamper restore (connection ok) '
985,0,15,'Exit time started '
986,0, 1,'Warning alarm '
987,0, 2,'Warning alarm cleared '
988,0, 1,'Arming aborted '
989,0, 7,'User logged in (INT-VG) '
989,1, 7,'User logged out (INT-VG) '
990,0, 4,'No connection with KNX system '
990,1, 4,'Connection with KNX system ok '
991,0, 1,'Zone auto-bypassed (tamper violations) '
991,1, 1,'Zone auto-unbypassed (tamper violations) '
- 20 -