Metro C200 Insulated Heated Cabinet - Manual (Page 4)

3
With the racks in the inboard position
(18" width), the following pans may be used:
3" Slide Spacing
16 pans — 18"x26"x2 5 /
8
"
32 pans — 12"x18"x2 5 /
8
"
32 pans — 13"x18"x2 5 /
8
"
17 pans — 14"x18"x2 5 /
8
"
Max. or combined pan size: 18"x27"x2 5 /
8
"
Min. pan width: 16"
4 1 /
2
" Slide Spacing
11 pans — 18"x26"x4 1 /
8
"
22 pans — 12"x18"x4 1 /
8
"
22 pans — 13"x18"x4 1 /
8
"
22 pans — 14"x18"x4 1 /
8
"
Max. or combined pan size: 18"x27"x4 1 /
8
"
Min. pan width: 18"
With the racks in the outboard position
(20" width), the following pans may be used:
3" Slide Spacing
17 pans — 15"x20"x2 5 /
8
"
34 pans — 10 7 /
8
"x19 3 /
4
"x2 5 /
8
"
34 pans — 11 1 /
8
"x20"x2 5 /
8
"
17 pans — 20"x20"x2 5 /
8
"
16 pans — 20"x22"x2 5 /
8
"
32 pans — 12"x20"x2 5 /
8
"
17 pans — 20"x24"x2 5 /
8
"
Max. or combined pan size: 20"x27"x2 5 /
8
"
Min. pan width: 16"
4 1 /
2
" Slide Spacing
11 pans — 15"x20"x4 1 /
8
"
22 pans — 10 7 /
8
"x19 3 /
4
"X4 1 /
8
"
22 pans — 11 1 /
8
"x20"x4 1 /
8
"
11 pans — 20"x20"x4 1 /
8
"
11 pans — 20"x22"x4 1 /
8
"
22 pans — 12"x20"x4 1 /
8
"
11 pans — 20"x24"x4 1 /
8
"
Max. or combined pan size: 20"x27"x4 1 /
8
"
Min. pan width: 18"
C. HOLDING MODULE
Equipped with a holding module, your cabinet
is designed to maintain the temperature of HOT
prepared foods.
The holding module is
equipped with a thermostatically controlled
heater, a blower for air circulation and a water
pan. A POWER switch is provided with a red
light to indicate when the unit is switched ON.
A TEMPERATURE thermostat and its yellow
indicator light are also provided along with a
thermometer.
A three-wire grounded lead cord is supplied
fixed to the module.
1. With POWER switch OFF, plug lead cord into
a standard grounded 20-amp, 125-VAC
receptacle.
2. To introduce limited humidity, fill the 1 1 /
2
-quart
capacity water pan to 1 /
2
" from top with HOT
clean tap water. During operation, check
water level every 3 hours and refill as
necessary. The unit may be operated without
water if humidity is not desired.
Above the water pan is an adjustable vent.
By rotating the vent open even more humidity
can be introduced into the cabinet.
3. Snap POWER switch to ON. The red light will
now glow as will the yellow indicator light,
and the blower will begin circulating air.
4. Turn the TEMPERATURE thermostat to
setting 10.
5. After allowing the cabinet to PREHEAT FOR
APPROXIMATELY 45 MINUTES, reduce the
thermostat setting to 8. In a room of average
temperature (72
°
F), this should provide
150
°
-170
°
F. Adjustments to the temperature
may be made as necessary.
NOTE: The red light will glow as soon as the
POWER switch is switched ON and will
continue to glow until switched OFF. The
yellow indicator light will go on and off as the
thermostat cycles the heat element. The
blower will operate as long as the POWER
switch is ON. If the yellow light is not
illuminated, this indicates that the cabinet has
achieved the preset TEMPERATURE level,
NOT that the unit has been switched OFF.
It is not necessary at the end of the operating
day to disrupt the TEMPERATURE setting in
order to turn the unit OFF. By switching the
POWER switch to OFF, the unit is no longer
operating. By switching the POWER switch to
ON when resuming operations, the cabinet
will attain the preset level.