Metro C200 Insulated Heated Cabinet - Manual (Page 3)

2
B. FEATURES — ALL MODELS
In order to utilize your new cabinet to its
full potential, take a minute to identify the
following features which have been provided
for your convenience.
• The module has been placed at the top
of the cabinet for easy accessibility and
efficient operation.
• Clearly-marked control panel angled for
easy viewing and climate adjustments
without opening the door.
• Removable water pan.
• Dutch-style insulated and gasketed doors.
• Heavy-duty magnetic door latches.
• All components — doors, module,
chimneys, slide racks — removable without
tools to permit thorough, obstruction-free
cleaning.
II. OPERATING INSTRUCTIONS
A. REVERSIBLE DOOR(S)
NOTE: Only the doors on the Non Pass-Thru
Models are field reversible.
The doors on your
Non Pass-Thru Cabinet can be reversed to
accommodate a right- or left-hand opening.
The cabinet has been shipped with the hinges
mounted on the right-hand side of the unit.
To reverse, follow the instructions listed below:
1. If the cabinet was in operation, allow
sufficient time for it to cool down to
comfortable level. Unlatch the doors, swing
open and lift vertically until clear of cabinet
mounted hinges. Place doors aside.
2. On the cabinet, remove the door strike plates
and hinges. Transfer them to the opposite
side of the cabinet. Install filler screws in the
original hinge and plate holes.
3. On the doors, remove the round covers from
the hinges. Also remove the screws securing
the hinges to the doors.
4. Rotate the hinges 180 degrees and
reassemble.
5. On the cabinet mounted hinges, lift the white
bushing vertically and rotate 180 degrees,
then seat.
6. Take the top door, rotate 180 degrees and
drop it onto the bottom cabinet mounted
hinges. Take the other door and drop it onto
the top mounted cabinet hinges.
7. Test doors to make sure gaskets are in
compression and the door latches hold
securely.
B. SLIDE RACK ASSEMBLIES
All models of slide racks are removable for
thorough cleaning.
On the inside of each cabinet are a series of
rack hangers. These hangers have two slots
for either an inboard or outboard rack
position. To remove the slide rack, grasp and
move upward until pins are free of hanger
slots. To install racks, locate pins over
hangers and lower until locked into the slots.
NOTE: For an inboard rack position, use the
slots farthest away from the inside wall of the
cabinet. For an outboard rack position, use
the slots closest to the inside wall of the
cabinet.
C4SC — Model 4 (3" Slide Spacing — fixed)
The Model 4 Slide Rack consists of two sets
of slides. Both sets can be installed either in
an inboard or an outboard position. Also, one
set of racks can be placed in the inboard
position while the second set can be
installed in the outboard position. All pans
are to be bottom loaded regardless of rack
positioning. The following pans may be used:
Inboard Hanger Position
(18" width)
17 pans — 18"x27"x2 5 /
8
"
17 pans — 14"x18"x2 5 /
8
"
Max. pan size: 18"x27"x2 5 /
8
"
Min. pan size: 17"
Outboard Hanger Position
(20" width)
17 pans — 20"x24"x2 1 /
4
"
17 pans — 20"x24"x2 5 /
8
"
34 pans — 12"x20"x2 1 /
4
"
34 pans — 12"x20"x2 5 /
8
"
Max. pan size: 20"x27"x2 5 /
8
"
Min. pan size: 19"
2C8SN—Model 28 (1 1 /
2
" Spacing — fixed)
The Model 28 Slide Rack can only be
installed in the inboard hanger position.
All pans are to be lip loaded. The following
pans may be used: 34 pans — 18"x26" max.
height 1
3 /
8
". Max. pan size: 18"x27"x1 3 /
8
"
Min. pan size: 18"
2CVSN—Model 2V (adjustable)
The Model 2V Slide Rack can be installed
in either an inboard or outboard position.
Center spacing on slides can be either 3"
or 4
1 /
2
". Slides can be removed by lifting
upward and sliding rivet heads out of the
keyhole slots. To install, select spacing, insert
rivet heads into keyhole slots and push down
until locked in hole. All pans are to be bottom
loaded regardless of slide or rack
positioning.