DeWalt DW744 - Manual (Page 5)

WARNING: For your own safety read instruction manual before operating table saw.
WARNING: When using electric tools, basic safety precautions should always be
followed to reduce risk of fire, electric shock, and personal injury, including the following:
Double Insulation
Double insulated tools are constructed throughout with two separate layers of electrical
insulation or one double thickness of insulation between you and the tool’s electrical system.
Tools built with this insulation system are not intended to be grounded. As a result, your
tool is equipped with a two prong plug which permits you to use extension cords without
concern for maintaining a ground connection.
NOTE: Double insulation does not take the place of normal safety precautions when
operating this tool. The insulation system is for added protection against injury resulting from
a possible electrical insulation failure within the tool.
CAUTION: WHEN SERVICING USE ONLY IDENTICAL REPLACEMENT PARTS.
Repair or replace damaged cords.
Polarized Plugs
To reduce the risk of electric shock, this equipment has a polarized plug (one blade is wider
than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully
into the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install
the proper outlet. Do not change the plug in any way.
Important Safety Instructions
• KEEP GUARDS IN PLACE and in working order.
• REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys
and adjusting wrenches are removed from tool before turning it on.
• KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries.
• DON’T USE IN DANGEROUS ENVIRONMENT. Don’t use power tools in damp or wet
locations, or expose them to rain. Keep work area well lighted.
• KEEP CHILDREN AWAY. All visitors should be kept safe distance from work area.
• MAKE WORKSHOP KID PROOF with padlocks, master switches, or by removing starter
keys.
• DON’T FORCE TOOL. It will do the job better and safer at the rate for which it was
designed.
• USE RIGHT TOOL. Don’t force tool or attachment to do a job for which it was not designed.
• USE PROPER EXTENSION CORD. Make sure your extension cord is in good condition.
When using an extension cord, be sure to use one heavy enough to carry the current your
product will draw. An undersized cord will cause a drop in line voltage resulting in loss of
power and overheating. The following table shows the correct size to use depending on
cord length and nameplate ampere rating. If in doubt, use the next heavier gage. The
smaller the gage number, the heavier the cord.
Minimum Gage for Cord Sets
Volts Total Length of Cord in Feet
120V 0-25 26-50 51-100 101-150
240V 0-50 51-100 101-200 201-300
Ampere Rating
More Not
more AWG
Than Than
0 - 6 18 16 16 14
6 - 10 18 16 14 12
10 - 12 16 16 14 12
12 - 16 14 12 Not Recommended
i• WEAR PROPER APPAREL. Do not wear loose clothing, gloves, neckties, rings, bracelets,
or other jewelry which may get caught in moving parts. Nonslip footwear is recommended.
Wear protective hair covering to contain long hair.
• ALWAYS USE SAFETY GLASSES. Also use face or dust mask if cutting operation is
dusty. Everyday eyeglasses only have impact resistant lenses, they are not safety glasses.
• SECURE WORK. Use clamps or a vise to hold work when practical. It’s safer than using
your hand and it frees both hands to operate tool.
• DON’T OVERREACH. Keep proper footing and balance at all times.
• MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for best and safest
performance. Follow instructions for lubricating and changing accessories.
• DISCONNECT TOOLS before servicing; when changing accessories, such as blades, bits,
cutters, and the like.
• REDUCE THE RISK OF UNINTENTIONAL STARTING. Make sure switch is in off position
before plugging in.
• USE RECOMMENDED ACCESSORIES. Consult the instruction manual for
recommended accessories. The use of improper accessories may cause risk of injury to
persons.
• NEVER STAND ON TOOL. Serious injury could occur if the tool is tipped or if the cutting
tool is unintentionally contacted.
• CHECK DAMAGED PARTS. Before further use of the tool, a guard or other part that is
damaged should be carefully checked to determine that it will operate properly and perform
its intended function–check for alignment of moving parts, binding of moving parts,
breakage of parts, mounting, and any other conditions that may affect its operation. A guard
or other part that is damaged should be properly repaired or replaced.
• DIRECTION OF FEED. Feed work into a blade or cutter against the direction of rotation of
the blade or cutter only.
• NEVER LEAVE TOOL RUNNING UNATTENDED. TURN POWER OFF. Don’t leave tool
until it comes to a complete stop.
• REPLACEMENT PARTS. When servicing, use only identical replacement parts.
Additional Safety Rules for Table Saw
WARNING: For your own safety, do not operate your saw until it is completely
assembled and installed according to the instructions and until you have read and
understood the following:
•
All Safety Rules • Adjustment Procedures
• Assembly Procedures • Basic Operations
• Operating Controls
• KEEP GUARDS in place and in working order.
• STABILITY. Make sure table saw is firmly mounted before use.
• MINIMIZE ACCIDENT POTENTIAL. Most accidents are caused by failure to follow setup
and operating instructions.
• AVOID awkward hand positions, where a sudden slip could cause a hand to move into a
saw blade or other cutting tool. Never reach in back of, or around, the cutting tool with
either hand to hold down the workpiece. DO NOT PLACE FINGERS OR HANDS IN THE
PATH OF THE SAW BLADE.
• NEVER reach under your machine when operating or make any adjustments when it is
running.
• SHUT OFF the saw and disconnect the power cord when removing the table insert,
changing the cutting tool, removing or replacing the blade guard, or making adjustments.
• ALWAYS maintain control of the workpiece. DO NOT let go of the workpiece until it is well
clear of the cutting tool.
• WHEN REMOVING short workpieces, or cleaning up around the table, be sure the saw is
in the OFF position and blade has stopped turning.
• NEVER turn the saw ON before clearing the table of all tools, wood scraps, etc., except
the workpiece and related feed or support devices for the operation planned.
1
English