Powermax30, Cut chart – Hypertherm Powermax30 Operator Manual User Manual
Page 72
OPERATION
4-10
powermax30
Operator Manual
Cut chart
The cut chart below is based on the use of 30-amp standard consumables and drag cutting.
Retaining cap
Nozzle
Electrode
Swirl ring
T30v torch
Optional
deflector
* To cut material thicker than 1/4 inch (6 mm), start torch at edge of material.
Material thickness
Material
Arc
current
(A)
Maximum
cutting speed
gauge or
inches
millimeters
inches per
minute
millimeters
per minute
18 ga.
1,3
Mild steel
30
394
10007
10 ga.
3,4
Mild steel
30
87
2210
3/16"
4,8
Mild steel
30
52
1321
1/4"
6,0
Mild steel
30
33
838
3/8"
9,0
Mild steel
30
15
381
18 ga.
1,3
Stainless steel
30
221
5613
10 ga.
3,4
Stainless steel
30
55
1397
1/4"
6,0
Stainless steel
30
24
610
3/8"
9,0
Stainless steel
30
11
279
18 ga.
1,3
Aluminum
30
399
10135
10 ga.
3,4
Aluminum
30
78
1981
1/4"
6,0
Aluminum
30
26
660
3/8"
9,0
Aluminum
30
11
279
PMX30_OM_04.qxp:PMX30_OM_04 10/7/09 12:45 PM Page 4-10
- EDGE Pro Ti Shape Cutting Control Rev.2 (288 pages)
- 80669J Rev.3 (304 pages)
- HD3070 Plasma Arc Cutting System w/ Manual Gas Console (281 pages)
- MAXPRO200 Rev.2 (294 pages)
- MicroEDGE Pro Shape Cutting Control Rev.2 (182 pages)
- Powermax1650 (317 pages)
- HPR260 Auto Gas Preventive Maintenance Program Rev.4 (288 pages)
- Shape Cutting Control (66 pages)
- PHC Sensor (58 pages)
- HTA Rev 6.00 Operators Manual (212 pages)
- HTA Rev 7.00 Install Guide (242 pages)
- THC Control Board Replacement (13 pages)
- THC Plasma Interfacer Upgrade (9 pages)
- THC X-Y Table Product Configuration (20 pages)
- D845GERG2 (128 pages)
- MRT2 (64 pages)
- MRT (98 pages)
- Duramax Hyamp Long Handheld Torches (92 pages)
- Duramax Hyamp Robotic Torch (74 pages)
- HyIntensity Fiber Laser Rev.3 (240 pages)
- PCBS-0124 (70 pages)
- SuperMicro 370SBA 533Mhz (90 pages)
- LR2075 (56 pages)
- Phoenix 8.0 (585 pages)
- LH2125 (60 pages)
- HD3070 w/ Automatic Gas (35 pages)
- HD3070 w/Manual Gas (43 pages)
- HD4070 Rev.8 (278 pages)
- HD4070 Product Configuration (88 pages)
- HPR800XD Manual Gas Preventive Maintenance Program Rev.1 (32 pages)
- HPR800XD Manual Gas Preventive Maintenance Program Rev.1 (33 pages)
- HPR800XD Manual Gas Rev.2 (368 pages)
- HPRXD Short Torch with Integrated Lead Rev.1 (30 pages)
- HT4001 (59 pages)
- DuraChill 5 HP Air-Cooled Chiller For Hypertherm (29 pages)
- HT4001 Air Injected Water Muffler System (40 pages)
- H601 Power Supplies (62 pages)
- MAX200 Remote Switch (9 pages)
- HT4100 Plasma Arc Cutting System Operating (50 pages)
- HT4001 Plasma Arc Cutting System (259 pages)
- HSD130 HySpeed Plasma (233 pages)
- HySpeed HT2000 Plasma Arc Cutting System Rev.7 (53 pages)
- HySpeed HT2000 Plasma Arc Cutting System Rev.27 (289 pages)
- MAX200 Water Muffler (39 pages)
- HT2000LHF Product Configuration (23 pages)