Delta Dore 620 DRIVER Installation User Manual
Page 2
To enter the configura-
tion menus:
- Turn the knob to
,
then press and hold
the
i
button for 5
seconds.
The unit will propose 2 configurations to choose
from:
After each menu has been configured, the unit returns
to the choice of menus.
If you want to exit configuration, turn the selector knob
to the right.
Configuration
B
as
ic config
u
r
a
tion
s
Unit reference n
u
m
b
er (for ex
a
mple, DRIVER 620)
Adv
a
nced config
u
r
a
tion
s
Unit ver
s
ion
Config
u
r
a
tion mode
5
s
ec.
Press button
2
.
To modify the various settings, press the + or - buttons,
then press the OK button to validate and go to the next
setting.
Advanced configurations (menu 2)
Modific
a
tion
au
thoriz
a
tion
for the
us
er
Progr
a
m modific
a
tion
au
thorized
Progr
a
m modific
a
tion
u
n
au
thorized
Basic configurations (menu 1)
Press button
1
.
To modify the various settings, press the + or - buttons,
then press the OK button to validate and go to the next
setting.
Progr
a
mming
type
s
election
Weekly (
b
y def
au
lt)
D
a
ily
Choix d
u
p
as
de
progr
a
mm
a
tion
p
as
d'1 he
u
re (p
a
r déf
au
t)
p
as
de
3
0 min
u
te
s
p
as
de 15 min
u
te
s
If there is a difference between the actual temperature
(taken with a thermometer) and the temperature mea-
sured and displayed by the unit, function 2-02 can be
used to compensate for the difference by changing the
way the sensor takes measurements.
Example: If the temperature
displayed by the unit is
19°C and the temperature
measured is 20°C, add 1°C
to the display and confirm
by pressing OK.
Correcting
the temper
a
t
u
re
me
asu
red.
Correction po
ss
i
b
le from -5°C to + 5°C
in increment
s
of 0.1°C.
Pre
ss
the + or –
bu
tton
s
to modify,
a
nd pre
ss
the OK
bu
tton to confirm.
The factory settings may be restored for each of the
menus.
Turn the knob to
, then press and hold the
i
button
for 5 seconds.
Repeat these steps for the other menus.
To exit the mode, turn the knob to another mode.
Return to the factory configuration
Hold down the men
u
bu
tton
yo
u
w
a
nt to reiniti
a
lize
for 5
s
econd
s
(ex
a
mple here with men
u
1).
Then pre
ss
the OK
bu
tton
to confirm the re
s
et.
Summary table of configurations
1-01
Type of program
0 = weekly
1 = daily
1-02
No program
0 = 1 hour
1 = 30 minutes
2 = 15 minutes
2-01
Modification authorization
0 = Program modifiable
1 = Non modifiable program
2-02
Correction of the temperature measured
by -5°C to +5°C in increments of 0.1°C.
Help
Nothing is displayed on the room unit screen.
There is no power supply.
Check the circuit breaker.
Pb — is displayed on the screen.
Problem with the connection on a Pilot Wire output.
Contact our technical department.
the
i
symbol flashes.
A fault is detected on the installation.
Press the button to view the fault(s).
The device displays: dEF and a number
There is a fault with the unit which requires a return to
our after-sales service.
Contact our technical department.
Technical characteristics
• 230 V, 50 Hz power supply, ±10%
• Consumption: 2 VA
• Class II insulation
• 1 or 2 pilot wires output 0.1A / 230V
• Clock backup in the event of a blackout:
2 hours (per capacitor)
• Dimensions: WxHxD = 80 x 103 x 16 mm
• Protection index: IP 30
• Installation in an environment with normal pollution
levels
• Storage temperature: -10°C to +70°C
• Operating temperature: 0°C to +40°C