Campomatic C964XRSIFSCN - Manual (Page 11)

11
� � � � � � �
�
�
�
�
�
�
ELECTRONIC PROGRAMMER
The programmer can select the following functions:
- Clock (set by keys 2 and 3)
- Minute counter (set by key 1)
- Cooking time (set by key 2)
- End of cooking (set by key 3)
- Manual operation mode (set by key 4)
- Setting time backwards (set by key 5)
- Setting time forward
(set by key 6)
The digital display (N) always shows the time and
can display cooking and end of cooking time or the
minute counter time by pressing the corresponding
push button.
N.B.: At the end of each setting session (except
for the minute counter) the programmer turns the
oven off. Check when next using the oven, if the
programmer is not going to be used, that the latter
is set on manual operation (see the instructions
given further on).
Setting the time (from 0.01 to 24.00 = hh,mm)
After connecting to the electricity mains or subsequent
to a power cut, AUTO and “0.00” will both flash
simultaneously on the display.
Press push buttons 2 and 3 simultaneously and start
setting the current time by pressing push button 5 or 6.
Once set the AUTO symbol will turn off and
the symbol, for manual operation, will turn on.
Minute counter (from 0.01 to 0.59 = hh,mm)
Press push button 1 and select cooking time with push
button 5 or 6. The symbol turns on. At the end of
the set time the buzzer will go off and the symbol
turns off.
Semi-automatic operation
(with cooking time from 0.01 to 23.59 = hh,mm)
By pressing push button 2 and setting the length of
cooking time with push button 5 or 6, the AUTO and
symbols will light up and stay on all the time. At
the end of the set time the symbol will turn off, the
AUTO symbol will flash and the buzzer will go off.
Semi-automatic operation
(with end of cooking time from 0.01 to 23.59 = hh,mm)
By pressing push button 3 and setting the end of
cooking time with push button 6, the AUTO and
symbols will turn on and stay on all the time. At the end
of the set time the symbol will turn off, the AUTO
symbol will flash and the buzzer will go off.
Automatic operation
(with the start of cooking time delayed)
First programme cooking time (both the AUTO and
symbol will turn on) and then the end of cooking time
(the symbol will turn off) as described previously.
The symbol will turn on again when baking in the
oven starts. At the end of cooking time the symbol
will turn off, the AUTO symbol will flash and the buzzer
will go off.
Manual operation
Manual operation is only possible when the automatic
programming has finished or after having cancelled
it by pressing push button 4. The AUTO symbol
disappears and the symbol turns on.
Buzzer
The buzzer will go off at the end of a programme or at
the end of the minute counter function and lasts about
7 minutes. The buzzer can be stopped by pressing
one of the function push buttons.
Programme start and control
The programme starts after setting. The programme
set can be controlled at any time by pressing the
corresponding push button.
Correcting/cancelling the programme setting
An automatic function programming error will occur if
the time shown on the clock is between the cooking start
time and cooking end time. This error will be signalled
immediately by a buzzer and the AUTO symbol will
flash. A setting error can be corrected by altering the
duration or end of cooking time. Any programme that
has been set can be corrected at any time by pressing
the corresponding programming key and then key 5 or
6. To cancel a programme, correct the time set bringing
it to a value of “0.00”. If functioning time is cancelled
the end of functioning is cancelled too and vice versa.
The oven turns off automatically and the AUTO symbol
flashes. Press key 4 to set the programmer on manual
operation. The right time cannot be corrected when
the automatic operation programme is working.
DESCRIPTION OF THE APPLIANCE