Audio Enhancement TLD100 - Manual (Page 31)

31
Command list
Command Content Type 1st parameter 2nd parameter Command example
QPW Query about this
unit power state
Query None None $QPW[CR][LF]
Response 1: POWER ON None $QPW:1[CR][LF]
CCS Notification of
microphone power
state
Change
notification
1: MIC1 input
2: MIC2 input
0: MIC OFF
1: MIC ON
$CCS:1:1[CR][LF]
QCS Query about
microphone power
state
Query 1: MIC1 input
2: MIC2 input
None $QCS:1[CR][LF]
Response Same as above 0: MIC OFF
1: MIC ON
$QCS:1:0[CR][LF]
SVL Volume setting Setting 1: MIC1 input
2: MIC2 input
L: LINE input
* Refer to “Volume
list” (page 32).
$SVL:L:00[CR][LF]
Response Same as above Same as above $SVL:L:00[CR][LF]
SVU Volume 1-step up Setting 1: MIC1 input
2: MIC2 input
L: LINE input
None $SVU:1[CR][LF]
Response Same as above None $SVU:1[CR][LF]
SVD Volume 1-step
down
Setting 1: MIC1 input
2: MIC2 input
L: LINE input
None $SVD:2[CR][LF]
Response Same as above None $SVD:2[CR][LF]
QVL Volume query Query 1: MIC1 input
2: MIC2 input
L: LINE input
None $QVL:1[CR][LF]
Response Same as above * Refer to “Volume
list” (page 32).
$QVL:1:01[CR][LF]
SMT Mute individual
setting
Setting 1: MIC1 output
2: MIC2 output
M: MIX output
0: MUTE OFF
1: MUTE ON
$SMT:1:0[CR][LF]
Response Same as above Same as above $SMT:1:0[CR][LF]
QMT Mute state query Query 1: MIC1 output
2: MIC2 output
M: MIX output
None $QMT:M[CR][LF]
Response Same as above 0: MUTE OFF
1: MUTE ON
$QMT:M:0[CR][LF]
SAM Mute collective
setting
Setting 0: MUTE OFF
1: MUTE ON
None $SAM:1[CR][LF]
Response Same as above None $SAM:1[CR][LF]
CPM Notification of
page mute state
Change
notification
0:PAGE MUTE OFF
1:PAGE MUTE ON
None $CPM:1[CR][LF]
QPM Query about page
mute state
Query None None $QPM[CR][LF]
Response 0: PAGE MUTE OFF
1: PAGE MUTE ON
$QPM:0[CR][LF]
CF1 Notification of F1
state
Change
notification
None None $CF1[CR][LF]
CF2 Notification of F2
state
* 3-time transmis-
sion at 1 sec.
interval
Change
notification
0: Non F2 status
1: F2 status & F2 ACK
signal not received
2: F2 status & F2 ACK
signal received
None $CF2:1[CR][LF]
QF2 Query about F2
state
Query None None $QF2[CR][LF]
Response 0: Non F2 status
1: F2 status & F2 ACK
signal not received
2: F2 status & F2 ACK
signal received
None $QF2:2[CR][LF]
SDS Microphone
Override setting
Setting 1: Microphone Override 0: Disable
1: Enable
$SDS:1:0[CR][LF]
Response Same as above Same as above $SDS:1:0[CR][LF]