Vectronics VEC-221K - Manual (Page 30)

VEC-221K Instruction Manual CW Memory Keyer Kit
25
H di-di-di-dit •••• U di-di-dah ••−
I di-dit
••
V di-di-di-dah
•••−
J di-dah-dah-dah •−−− W di-dah-dah •−−
K dah-di-dah
−•−
X dah-di-di-dah
−••−
L di-dah-di-dit •−•• Y dah-di-dah-dah −•−−
M dah-dah −− Z dah-dah-di-dit −−••
1 di-dah-dah-dah-dah
•−−−− 6 dah-di-di-di-dit −••••
2 di-di-dah-dah-dah ••−−− 7 dah-dah-di-di-dit −−•••
3 di-di-di-dah-dah •••−− 8 dah-dah-dah-di-dit −−−••
4 di-di-di-di-dah ••••− 9 dah-dah-dah-dah-dit
−−−−•
5 di-di-di-di-dit ••••• 0 dah-dah-dah-dah-dah −−−−−
Period [.]
di-dah-di-dah-di-dah •−•−•− AAA
Comma [,] dah-dah-di-di-dah-dah −−••−− MIM
Question Mark or
Request for Repetition
[?] di-di-dah-dah-di-dit ••−−•• IMI
Fraction Bar [/] dah-di-di-dah-dit −••−• DN
End of Message or Cross [+] di-dah-di-dah-dit •−•−• AR
End of Work di-di-di-dah-di-dah •••−•− SK
Double Dash, Pause or Break [=] dah-di-di-di-dah −•••− BT
Semicolon [;] dah-di-dah-di-dah-dit
−•−•−•
KR
Colon [:] dah-dah-dah-di-di-dit −−−••• OS
Apostrophe ['] di-dah-dah-dah-dah-dit •−−−−• WG
Quotation Mark ["] di-dah-di-di-dah-dit •−••−• AF
Hyphen or Dash [-] dah-di-di-di-di-dah −••••− DU
Underline [_] di-di-dah-dah-di-dah
••−−•−
IQ
Dollar Sign [$] di-di-di-dah-di-di-dah •••−••− SX
Left Parenthesis [(] dah-di-dah-dah-dit
−•−−•
KN
Right Parenthesis [)] dah-di-dah-dah-di-dah −•−−•− KK
Wait di-dah-di-di-dit •−••• AS
Understood di-di-di-dah-dit •••−• SN
Starting Signal dah-di-dah-di-dah −•−•− KA
Error di-di-di-di-di-di-di-dit •••••••• HH
Paragraph [¶] di-dah-di-dah-di-dit •−•−•• AL
Invitation to Transmit dah-di-dah −•− K
1. FCC test requirement consists the 26 letters, the 10 numerals, the period, the comma, the question mark, AR , SK , BT and DN .
IN CASE OF DIFFICULTY
Only high-quality components and proven circuit designs are used in Vectronics
kits. In very rare instances is a defective component the source of a problem.
Replacement of defective parts is covered in the Warranty section. Ninety-five
percent of the kits returned for factory repair are due to soldering problems or
parts in the wrong locations. We advise repeating the assembly instructions
step-by-step, looking for mistakes or soldering problems. Be especially wary of
electrolytic capacitors and semiconductors. Kit builders often miss obvious