Pengo DT-5 - Manual (Page 11)

Two Speed (DT & RT) Series Manual 11
PRODUCT SPECIFICATIONS
TOTAL UNIT WEIGHT 645 LBS / 292 Kg
HYDRAULIC MOTOR INFORMATION
Displacement 11.9 cu/in (195cc)
Motor Type Two Speed Bi-Directional
Motor Output Shaft 1-1/4" Spline 14T
Motor Mount SAE - C 4 Bolt
Motor Ports 1-5/8" - 12 UN-2B
Cross Over Pressure Relief Set @ 3100 psi
PLANETARY GEARBOX INFORMATION
Gearbox Type Planetary Two Stage
Reduction Ratio 25.36:1
Output Shaft 2-1/2" Hex
Oil Capacity 2.0 Gallons
Oil Type SAE 80W90 GL-5
Shaft Pull Out (lbs.) 22,500 lbs.
REFERENCE TORQUE CHART
Pressure PSI (Bar) High Torque (ft/lbs) Low Torque (ft/lbs)
1600 (110) 5253 2626
1800 (124) 5910 2954
2000 (137) 6567 3283
2200 (151) 7223 3611
2400 (165) 7880 3940
2600 (179) 8536 4268
2800 (193) 9193 4596
3000 (206) 9850 4925
REFERENCE SPEED CHART
Flow GPM (Liter) Low Spd (rpm) High Spd (rpm)
20 (75) 13 25
30 (113) 19 38
40 (151) 25 50
50 (190) 31 63
AUGER DRIVE MODEL
rt-9
TOTAL UNIT WEIGHT 655 LBS / 297 Kg
HYDRAULIC MOTOR INFORMATION
Displacement 14.9 cu/in (244cc)
Motor Type Two Speed Bi-Directional
Motor Output Shaft 1-1/4" Spline 14T
Motor Mount SAE - C 4 Bolt
Motor Ports 1-5/8" - 12 UN-2B
Cross Over Pressure Relief Set @ 3100 psi
PLANETARY GEARBOX INFORMATION
Gearbox Type Planetary Two Stage
Reduction Ratio 25.36:1
Output Shaft 2-1/2" Hex
Oil Capacity 2.0 Gallons
Oil Type SAE 80W90 GL-5
Shaft Pull Out (lbs.) 22,500 lbs.
REFERENCE TORQUE CHART
Pressure PSI (Bar) High Torque (ft/lbs) Low Torque (ft/lbs)
1600 (110) 6576 3068
1800 (124) 7398 3451
2000 (137) 8220 3835
2200 (151) 9042 4219
2400 (165) 9864 4603
2600 (179) 10686 4986
2800 (193) 11508 5369
3000 (206) 12330 5753
REFERENCE SPEED CHART
Flow GPM (Liter) Low Spd (rpm) High Spd (rpm)
20 (75) 10 21
30 (113) 15 31
40 (151) 21 41
50 (190) 26 51
AUGER DRIVE MODEL
rt-12
Two speed models must have a minimum of 20GPM.
Output speed and torque specifi cations are NOT listed at 100% effi ciency. Maximum effi ciencies have been applied to the torque
and speed charts according to the manufacturers recommendations. Speed and torque output are dependant on the overall
system effi ciencies associated with the prime movers hydraulic system. When the purchaser is determining criteria for specifi c
applications please contact Pengo. Pengo has made every attempt to present accurate and suitable information published on this
document. This document should be used for information and comparative purposed only. When application specifi c information is
required, please contact Pengo.
Pengo continually looks for new ways to improve its products. Therefore, Pengo reserves the right to make changes to our
products and specifi cations without notice.