Hardware specifications – NEXCOM NViS 2310 User Manual
Page 17
Copyright © 2013 NEXCOM International Co., Ltd. All Rights Reserved.
3
Chapter 1: Product Introduction
NViS2310 User Manual
Hardware Specifications
CPU
▪ Intel
®
Atom™ processor quad core E3845, 1.91GHz
Memory
▪ 1x 204-pin DDR3L SO-DIMM socket support 1066MHz/1333MHz up to 8GB.
Default 4GB
Storage
▪ 1x 2.5” SSD/HDD SATA 2.0
(externally accessible, optional lockable storage available)
▪ 1x CFast (externally accessible)
Expansion
▪ 1x full size Mini-PCIe socket (USB 2.0)
▪ 1x full size Mini-PCIe socket (USB 2.0)
▪ 1x full size Mini-PCIe socket (USB 2.0 + PCIe)
▪ 1x half size Mini-PCIe socket (USB 2.0 + PCIe)
Function
▪ 1x default U-blox UBX-G6010 GPS module (50-channel and Galileo) or
optional modules with Dead Reckoning or GLONASS support
▪ Built-in G-sensor
I/O Interface-Front
▪ 4x LED for power, storage, WWAN, WLAN
▪ 2x externally accessible SIM card socket (selectable)
▪ 1x phone jack 3.5mm for 1x Mic-In
▪ 1x phone jack 3.5mm for 1x Line-Out
▪ 1x externally accessible 2.5” SATA 2.0 SSD/HDD tray
▪ 1x externally accessible CFast card socket with cover
▪ 1x event button (trigger type)
▪ 1x reset button
▪ 1x type A USB 3.0 compliant host, supporting system boot up
▪ 4x antenna hole for WWAN/WLAN/BT
I/O Interface-Rear
▪ 1x 9~36VDC input with ignition and 19W typical power consumption
▪ 2x type A USB 2.0 compliant host, supporting system boot up
▪ 2x RJ45 10/100/1000 Fast Ethernet with LED
▪ 1x phone jack 3.5mm for 1x Mic-In
▪ 1x phone jack 3.5mm for 1x Line-Out
▪ 1x DB-15 VGA, resolution up to 2560 x 1600 @60Hz
▪ 1x DP port, resolution up to 2560 x 1600 @60H
▪ 1x antenna hole for GPS
▪ 2x DB-9 RS-232 (RI/5V/12V selectable)
▪ 1x DB-9 RS-422/485
▪ 1x DB-9 for CAN 2.0B (optional CAN Bus 2.0B Mini-PCIe card),
2x MCU-DI and 2x MCU-DO
▪ 1x 16-pin terminal block
- 1x CAN Bus 2.0B (on board)
- 1x optional OBDII module (SAE J1939 or J1708)
- 8x GPIO (Programmable or optional isolation)
Digital Input (internal type): 5VDC TTL (default)
Digital Input (source type): 3~12VDC
Digital Output (sink type): 5VDC TTL (default), max current: 20mA
Digital Output (source type): 3~24VDC, max current: 150mA
▪ 1x 12VDC output (2A), SM Bus
Power Management
▪ Selectable boot-up & shut-down voltage for low power protection by
software
▪ Setting 8-level power on/off delay time by software
▪ Status of ignition and low voltage can be detected by software
▪ Support S3/S4 suspend mode