Dynex DX-LDVD19-10A - Manual (Page 14)

10
Turning on your TV for the first time DX-LDVD19-10A
Connecting a component video device
To connect a component video device:
1 Make sure that your TV’s power cord is unplugged and the
component video device is turned off.
2 Connect a component video cable to the COMPONENT OUT jacks
on the component video device.
3 Connect the other end of the component video cable to the
COMPONENT IN jacks on the back of your TV.
4 Connect an audio cable to the AUDIO OUT jacks (L/R) on the
component device.
5 Connect the other end of the audio cable to the
COMPONENT AUDIO-R and AUDIO-L jacks on the back of
your TV.
To play from a component device:
1 Turn on your TV, then press INPUT to select Component.
2 Turn on the component video device and set it to the correct
output mode. See the component video device’s user guide for
more information.
Connecting a computer
Tip: Some computers have an HDMI connector, which can be used for a
better picture.
To connect a computer:
1 Make sure that your TV’s power cord is unplugged and the
computer is turned off.
2 Connect a VGA cable (not provided) to the VGA jack on the
computer, then connect the other end of the cable to the VGA IN
jack on the back of your TV.
Note: The VGA cable should be a 15-pin D-Sub (analog RGB) cable.
3 Connect an audio cable to the AUDIO OUT jack on the computer,
then connect the other end of the cable to the PC AUDIO IN jack
on the back of your TV.
Note: The audio cable should have a stereo mini plug.
To play video from a computer:
1 Turn on your TV, then press INPUT to select VGA.
2 Turn on the computer, then check the image on your TV. There
may be noise associated with the resolution, vertical pattern,
contrast, or brightness in VGA mode. If noise is present, change
the PC mode to another resolution, change the refresh rate to
another rate, or adjust the brightness and contrast on the menu
until the picture is clear. If the refresh rate of the PC graphic card
can not be changed, change the PC graphic card or consult the
manufacturer of the PC graphic card.
Note: All above listed are subject to VESA criteria.
Turning on your TV for the first
time
To turn on and configure your TV:
1 Make sure that you have inserted the batteries in the remote
control, connected the antenna to the TV, and connected the AC
power.
2 Press POWER , then wait several seconds. The power indicator
LED turns blue and the TV turns on.
3 Select the signal source for your TV.
• Press INPUT to open the signal source menu, then press
CH+ or CH- to select the source. Options include:
• TV
• Composite
• S-Video
• Component
• DVD
• VGA
• HDMI
• Press ENTER/VOL+ to confirm.
4 Select the TV signal source for your TV and auto scan for
channels.
• Press MENU, then press VOL+/VOL- to highlight
CHANNELS.
• Press ENTER/VOL+. The Channels menu opens.
COMPONENT
IN
Y
Pb
Pr
S-
V ID
EO
IN
AU
DI
OI
N
L
R
Back of TV
C
o
m
p
o
n
en
t vi
d
e
o c
a b
les
Au
di
o ca
bl
e s
Component video device
Note: Cables are
often color-coded
to connectors.
PC
AU
DIO
IN
VGA
IN
Audio cable (stereo mini plugs)
D-Sub cable (analog RGB)
Back of TV
Computer
Mode Resolution
Line freq
(KHz) Frame freq
(Hz)
VGA 640x480 31.5 60
SVGA 800x600 37.9 60
XGA 1024x768 48.4 60
1280x720 45 60
1280x768 47.45 60
1360x768 47.7 60
MOVE SELECT PREVIOUS EXIT ENTER MENU EXIT
PICTURE
Channels
AUDIO CHANNELS SETTINGS
Off
Auto Channels Search
Add/Skip Channels
Audio Only
Favorites
Channel Labels
Channel Strength
VOL -
CH+
CH-
VOL +
DX-LDVD19-10A_09-0340.book Page 10 Tuesday, April 28, 2009 4:43 PM