SkyRC 6x80+ Blue Version Charger - Manual (Page 12)

20 21 6X80 Plus 6X80 Plus
NIMH/NICD BATTERY PROGRAM
These programs are for charging or discharging NiMH (Nickel-Metal-
Hydride) or NiCd (Nickel-Cadmium) battery.
CHARGING OF / BATTERY NIMH NICD
The charger will charge NiMH and NiCd batteries using the charge
current set by the user.
NiMH CHARGE
CURRENT 2.0A
Battery
type - +
Elapsed
time
Charged
capacity Battery
type Charge
current
Battery
voltage
> 3 seconds
The screen displays the current state of
charging.
To stop the process, press Mode/Stop
button once.
The audible sound indicates the end of
process.
This program is for charging of NiMH/NiCd
batteries. You can press Start/Enter dial to
make the parameter blink, then rotate the
dial to change the value and repress the dial
to store the value.
CHARGING / BATTERY IN THE AUTO
CHARGE MODE
NIMH NICD
In this program the charger detects the condition of the battery which is
connected to the output and automatically charges the battery. In this
mode, you should set up the upper limit of the charge current to avoid
damage by excessive feeding current. Some batteries of low
resistance and capacity can lead to higher current in the auto charging
mode.
N i M H A u t o C H A R G E
C U R R E N T 2 . 0 A
This program is for charging of NiMH/NiCd
batteries in auto mode. You can press
Start/Enter dial to make it blink and then rotate
the dial to change the parameter value. Press
START/ENTER dial to store the value.
SELECT
Mode
Stop
Battery
type
> 3 seconds
Mode
Stop
Press
Dial
Press
Dial
N i M H 2 . 0 A 9 . 5 2 V
A U T 0 0 0 : 1 3 0 0 0 0 0
CHARGING / BATTERY IN RE-PEAK
CHARGE MODE
NIMH NICD
Re-peak Charge Mode (NiMH and NiCd batteries only): In re-peak
charge mode, the charger can peak charge the battery once, twice or
three times in a row automatically. This is good for confirming the
battery is fully charged, and for checking how well the battery receives
fast charges. A five minute cool-off delay occurs after each re-peak
charge. To start charge, press and hold the dial for 3 seconds.
NIMH/NICD BATTERY PROGRAM
The screen displays the current state of
charging.
To stop the process, press Mode/Stop
button once.
The audible sound indicates the end of
process.
Elapsed
time
Charged
capacity
Battery
type
Charge
current
Battery
voltage
N i M H R E - P E A K
1
N i M H 2 . 0 A 9 . 5 9 V
R P C 0 0 0 : 3 3 0 0 0 1 7
Re-peak cycle number 1 shows on the display.
Press the dial to make the re-peak cycle
number blink and rotate the dial to find the
desired number of times to re-peak charge the
battery.
Press the dial to confirm selection.
- +
SELECT
Battery
type
Charge
current Battery
voltage
Elapsed
time Charged
capacity
DISCHARGING OF / BATTERY NIMH NICD
NiMH DISCHARGE
0.1A CUT:1.0V
Battery
type
- +
> 3 seconds
Set discharge current on the left and final
voltage on the right. The discharge current
ranges from 0.1 to 5.0A and the final voltage
ranges from 0.1 to 25.2V. To start the
process, press and hold Start /Enter dial for
3 seconds.
Mode
Stop
SELECT
Press
Dial
Press
Dial