Lumagen VisionHDQ - Manual (Page 32)

VisionHDQ ™
User Manual and Installer Guide
© 2004-2007 Lumagen®, Inc. 29 Rev 1.14
l
LBOX
Input is 4:3 letter-box format (lower-case L). Use previous zoom setting
]
LBOXNZ
Input is 4:3 letter-box format (lower-case L) . No zoom
w
16:9
“Enhanced for 16:9 televisions” format. Use previous zoom setting
*
16:9NZ
“Enhanced for 16:9 televisions” format. No zoom
j
1.85
Input is 1.85 format. Use previous zoom setting
/
1.85NZ
Input is 1.85 format. No zoom
W
2.35
Input is 2.35 format. Use previous zoom setting
a
MEMA
Select MEMA
b
MEMB
Select MEMB
c
MENC
Select MEMC
d
MEND
Select MEMD
g Onscreen messages on
s Onscreen messages off
z
FREEZE
Freeze-frame. Any other character resumes
Y
YPRPB
Output type is HD color-space YPRPB (component)
R
RGBHV
Output type is RGBHV. completes command
S
RGBS
Output type is RGBS. completes command
T
RGsB
Output type is RGsB. co mpletes command
A
480P
Select Vertical Resolution = 480p
B
540P
Select Vertical Resolution = 540p
C
600P
Select Vertical Resolution = 600p
D
720P
Select Vertical Resolution = 720p
E
768P
Select Vertical Resolution = 768p
F
840P
Select Vertical Resolution = 840p
G
1080P
Select Vertical Resolution = 1080p
I
1080I
Select Vertical Resolution = 1080I
V
VRES
Set Vertical Resolution (e.g. V960 , for 960p)
~
VRATE
Set Vertical rate (e.g. ~5994 , for 59.94 Hz)
H
HRATE
Set Horizontal Rate (e.g. H45000 for 45KHz)
=
ASPECT
Set Output aspect ratio (e.g. =178 for 16:9 displays)
tXMM
Test Pattern command: X is a letter ‘a’-‘p’ corresponding to the 16
available patterns. MM is the ire level divided by 10, so 0-10. Sending
‘X’ will exit the pattern display.
ZT1xxxx
Print a message on the screen for 5 seconds. The command always
begins with the characters "ZT", followed by a single digit which sets
the duration of the message. '0' for 2 seconds, '1' for 5 seconds, '2' for 10
seconds and so on, with '9' leaving the message onscreen until a "ZC" is
sent or a Lumagen remote control command clears the message. The
message string “xxxx” which follows the duration digit can be up to 30
characters in length. The '@' character font is replaced with a solid block
for use as a volume bar. Legal characters must be in the range of ' ' thru
'z' (which is 0x20 - 0x7a in hex). Anything outside that range such as
carriage return or even the '{' can be used to terminate the message
command.
ZC Clear any onscreen messages .
ZY0M
Set zoom factor to M. Where M can be 0-2, or 0-7 if zoom is set for 5%
steps.
ZY1MMM
Set output aspect ratio to MMM. Where valid range is 110-250 which
corresponds to 1.10 to 2.50.
ZY1MMMNNN
OOOPPP
Set output shrink parameters. Where MMM=top, NNN=left,
OOO=bottom, PPP=right edge. Range is 0-255 for each.