Autostart AS-6205i SH - Manual (Page 10)

The Programming
Assistance Button (A.k.a.
PAB.)
The PAB is located on the
side of the Module. This
push button mimics the
Hood-Pin switch in order to
avoid having to get out of
the vehicle and pressing the
Hood-Pin switch. The PAB
will work only when the
Hood Is up.
How to Program the Transmitter.
1. FLASH the Hood Pin Switch.
Before the 20 seconds have passed, turn the Ignition Key to the ignition on ( run ) position.
Turn the ignition to off .
2. Press and hold the lock button until the vehicle gives 5 flashes. The Module has
stored the Transmitter in its memory.
3. Close the Hood, to exit.
Table 1
The Module has the ability to retain up to 4 different Transmitter codes; if a fifth Transmitter is
programmed, the code of the first Transmitter will be erased from memory. To erase all
Transmitter codes from memory, you must perform a Module reset (See “Resetting the
Module” on page 18 ).
To program the Transmitter on a second vehicle (Multi-car Operation),
you must press the trunk button (of the secondary Transmitter you wish to
program) during step 2 of Transmitter Programming.
How to Enter Options Programming Mode
The System is equipped with three custom Programming Modes, allowing the installer to
custom-fit the system according to the requirements of each vehicle. When getting into the
Programming Option Mode, the Parking Lights and the Siren will flash and chirp once, twice
or three times depending on the option you have entered. The unit will stay in Programming
Mode until the Hood Pin-switch or the Brake Pedal is pressed again. Therefore take your time
to make the proper selection. To return to the Programming Centre (Main Menu), press on
the Brake Pedal.
1. FLASH the Hood Pin Switch.
Before the 20 seconds have passed,
2. Press and hold the Brake Pedal, then press one of the following buttons on the
Transmitter:
• LOCK to enter Mode 1 ;
• UNLOCK to enter Mode 2; or
• TRUNK to enter Mode 3.
The Parking Lights and the Siren will flash and chirp once, twice or 3 times to confirm
entry Into a Mode.
The Module can only be programmed Function by Function. After selecting a Mode
(from 1 to 3), you will be taken to the first Function of that Mode. After entering an Option
number for Function 1, you will be automatically taken to Function 2, and so on; therefore, be
ready to re-enter all option numbers for all functions of the Mode you are accessing. You
may not skip Functions.
For each Function, select one of the four Options by pressing the corresponding
button on the Transmitter:
• LOCK for Option 1,
• UNLOCK for Option 2,
• TRUNK for Option 3, or
• START for Option 4.
Table 3
Once an Option has been selected the Parking Lights will flash 1, 2, 3 or 4 times depending
on the selected Option. At any time, you can press the Brake Pedal to return to the
Programming Centre (Programming Modes and Tach Programming).
Options Programming
3. Release the Brake Pedal.
Table 2
Mode 1 *indicates default setting
Function 1 - Ignition-Controlled Door locks
option 1* Ignition Lock DISABLED
OPTION 2 Ignition Lock ENABLED
OPTION 3 Ignition unlock only
OPTION 4 Ignition lock only
Function 2 - Secure Lock
option 1* Secure Lock disabled (1-sec. Disarm pulse.)
OPTION 2 Secure Lock enabled in Smart Mode.
OPTION 3 Secure Lock disabled (0.5 Sec Disarm pulse)
OPTION 4 Secure Lock enabled in Normal Mode.
Function 3 - Door Locks Pulse Timing
OPTION 1* 7/10 Second Lock/Unlock pulses.
OPTION 2 4 Seconds Lock/Unlock pulses.
OPTION 3 7/10 Seconds Lock pulse and two 1/4 second unlock pulses.
OPTION 4 1/10 Second Lock/Unlock pulses.
Function 4 - AUX 3 Programming
OPTION 1* Constant while the TRUNK button Is pressed
OPTION 2 1 -sec. Trunk 1 output when TRUNK button pressed for 3 sec. while Ignition is OFF
and Data output.
OPTION 3 TRUNK with Disarm/Rearm (Shock is ignored while Zone 3 is opened.)
OPTION 4 TRUNK 1 sec output ON/OFF
Function 5 - AUX 2 Programming
OPTION 1* Priority Door access (Pressing UNLOCK a 2 nd time triggers AUX 2)
Car Finder enabled (pressing LOCK and UNLOCK triggers Car Finder)
The Driver’s Door unlocks upon the 1st pressing of the UNLOCK button;
All Doors unlock on any subsequent pressing of the UNLOCK button.
OPTION 2 Toggle ON/OFF with a 30-second timeout (press LOCK and UNLOCK)
Car Finder disabled.
OPTION 3 Constant output while pressed (press LOCK and UNLOCK)
Car Finder disabled.
OPTION 4 Priority Door access on 2 nd Unlock, and Car Finder enabled.
• The Driver’s door unlocks upon the 1 s *, 3 rd , 5 th > pressing of the UNLOCK button.
P.10 Installation Guide AS-6205Í SH AS-6205Í SH Installation Guide P.11