Aiphone Ccs 1a - Manual (Page 4)

WIRING DIAGRAM
MOUNTING
CC-DA mounts on surface of wall with 2 screws.
CC-DA
(101.5mm)
CC-1M
2 wood screws supplied
SINGLE-GANG BOX or WALL
1. Attach the mounting bracket to box or wall.
2. Mount the CC-1M station on the bracket.
2 screws supplied
OPERATIONS--------------------------------------
At CC-DA door, press CALL button (backlit) once. A muted
chime will be heard at the door. At CC-1 M room station(s), 2-
tone chime sounds. Press TALK button to transmit, and release
to listen. The system automatically turns off in 15 seconds after
last time the TALK button is pressed. Press TALK button to
recycle.
• Chime & voice volume adjustments:
CHIME VOICE
CC-1 M bottom view
L H
TECHNICAL PRECAUTIONS-------------------
• CCS-1A components are not compatible with C-123L/A units.
• In 2-CC-1M system;
1. There is no calling between CC-1 M stations.
2. If both CC-1 M's press the TALK button (meaning both
masters are on), a squeal will be heard when either CC-1 M
presses the TALK button. Wait until system turns itself off
before using.
• To prevent acoustic feedback;
Do not mount a door station & a room station back to back on
a common wall. With conduit wiring, pack conduit with foam or
insulation for best results.
• CC-DA is weather resistant. If possible and for best results,
install the door station in an area not directly exposed to
weather.
• Do not apply caulking or sealant around door station, so the
openings allow moisture to dissipate.
• Do not put direct pressure water on CC-DA door station.
• Clean CC-1M unit with a soft cloth dampened with neutral
household cleanser. Never use any abrasive cleaner or cloth.
4^ SPECIFICATIONS (CC-1M)--------------------
• Power source: 12-16V AC, 10VA.
• Power supply: AC transformer PT-1210N in USA (specified)
or 12-16V 10VA AC (with no-load voltage
rating: 20V or less).
• Communication: 2-tone chime call-in.
Press “TALK” button on room station to talk,
release to listen. Hands free at door. 15 sec.
time out after last time TALK button released.
•Controls: CHIME vol. VOICE vol.
• Wiring: 2 parallel wires, non-polarized to door.
2 wires to another room, polarized.
2 wires to PT-1210N (from ea. CC-1 M)
Distance:
22AWG(O.65mm0) 18AWG(1.Omm0)
CC-DA to CC-1M (or 2nd) 245’(75m) 590'(180m)
CC-1 M to AC transformer 65’(20m) 145'(45m)
• Dimensions & weight:
CC-1M: 7"H X 4-3/4”W x 1-5/16”D. 180H x 123W x 33D (mm). 400g (0.88lbs.).
CC-DA: 4-1/2”H x 2-3/4”W x 1-3/16”D. 114H x 70W x 30D (mm). 150g (0.33lbs.)
•« <
^ WARRANTY
Aiphone warrants its products to be free from defects of material and workmanship under normal use and service for a period of one
year after delivery to the ultimate user and will repair free of charge or replace at no charge, should it become defective upon which
examination shall disclose to be defective and under warranty. Aiphone reserves unto itself the sole right to make the final decision
whether there is a defect in materials and/or workmanship; and whether or not the product is within the warranty.
This warranty shall not apply to any Aiphone product which has been subject to misuse, neglect, accident, or to use in violation of
instructions furnished, nor extended to units which have been repaired or altered outside of the factory. This warranty does not cover
batteries or damage caused by batteries used in connection with the product.
This warranty covers bench repairs only, and any repairs must be made at the shop or place designated In writing by Aiphone.
Aiphone will not be responsible for any costs incurred involving on site service calls.
».
4 V-
«
1
«
4
Aiphone Co., Ltd., Nagoya, Japan
Aiphone Corporation, Bellevue, WA, USA
CCS-IA-I(E) 0697B
#90115
o
♦1-
♦i*
-I-
COMMUNICATION SYSTEMS
AIPHONE
HOME, BUSINESS, INDUSTRY.
Printed In Hong Kong (E)
-4