Audiovox SP85 - Manual (Page 8)

HANDS-FREE OPERATION
(NAM OPTION)
This feature permits you to engage in the conversation
without lifting the handset.
1. After receiving a call (press I SND I to answer),
conduct the conversation via the hands-free
external microphone and the loudspeaker in the
cradle. To engage the conversation more naturally;
a. Speak in a normal tone.
b. It is preferable to turn-off the radio or stereo
and close the car windows.
2. To originate a call, enter the telephone number, then
press [SNDl. The microphone will be turned on,
ready for conversation when your party answers.
3. After a call is completed. Press I END I to terminate
a call.
Note: 1. When this option is activated, as the unit
always operates in Hands-free Mode, you
should press I END I to terminate a call.
2. Even if this option is installed, you can
of course engage the conversation via the
handset, but you have to press
lENDI to
terminate a call.
3. When you hear feedback on a bad RF
Channel, adjust the hands-free loop
attenuation as follows.
(1) Press IFUNCI, key I 7 I then |~2l.
hands-free loop attenuation will be
increased by 6 dB.
(2) To return to the normal condition,
press
IFUNCI, key then [1].
END to END SIGNALING
This feature permits you to utilize some additional
services, such as accessing discounted long distance
network, signal pager, or banking by phone e.t.c.
For these services the signaling should be in DTMF
(Touch Tone^“). The following features will make it
easier to send DTMF codes.
Touch Tone’^®^ from Memory
DTMF signaling by repertory dialer is available while
engaged in a telephone conversation.
1. Press [RCniRCLl, then enter the repertory
memory address (01 through 50).
The last ten digits of the number will appear on
the readout.
2. Press I SND I . Then DTMF signal will be sent
and monitored through the loud speaker.
Link Dialing
This feature permits you to pre-set from repertory
memory or key pad up to five numbers before
originating a call.
With this feature, the first number is sent in digial
form to the cell-site. Then up to four other numbers
can be sent with DTMF signaling by simply pressing
I SND I for each additional number.
Notes. (1) Each number to be linked may be
recalled from memory or entered by
key pad.
(2) Each number to be linked should be
within 16 digits including linking mark
I = I at the end.
(3) Linked number can be stored in the
memory. However, the total number of
digits must be less than 16 digits.
Example : To access the Discounted Long Distance
Call.
To access the discounted long distance call, you
should call your Long Distance Service Office first, and
enter your ID number, then the telephone number to
be placed.
1. Recall the Telephone Number of the Long Distance
Service Office.
I7|4|6l3|4|7|9l
2. Press IFUNCI, then [^.
Linking mark “ = ” will be added at the end of the
number, and |
Link 1 | will appear in the display.
r7|4|6|3i4|7|9|= I
3. Recall your ID number.
|6|7|1I4|8I5|21
4. Press IFUNCI, thenB
|6|7|1|4|8|5|2|=|andrLEk^
Recall the telephone number to be called.
a
^I4|5l6l7l8|9|0|
6
. Press |SND|. The I IN USE lindicator will light as
the call is placed. I Link 1l will appear in display.
7. After you received the signal from the Long
Distance Service Office, press | SND | again. The
DTMF signal will be sent and your ID number
will be monitored through the loud speaker.
I Link 2 I will appear in display.
8. If your ID number is accepted, the Long Distance
Service Office will signal again, so press rSNDl.
14 15