beautypg.com

26478 craftsman router table floor stand, 25333 craftsman industrial router adapter plate, Introduction – Sears 26462_0 User Manual

Page 5: Optional router table accessories, Unpacking and checking contents

Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".

background image

switch box when turning the router ON or OFF. DO
NOT touch anything but the switch box when doing

this. NEVER reach under the router table for any rea­

son when the router is running, except to turn it OFF.

A

warning

24. L™------------------ Before making any cut, make
sure the router is turned OFF, the router bit is not

rotating, and the power cord is unplugged from the
electrical outlet. Then, make absolutely sure that the
overhead guard clears the router bit and the work­
piece. A trial pass, with the router turned OFF and the
router bit not turning, is strongly recommended.

A

warning

25. L"-------------------- Never leave the router table
unattended while the router is running. Turn the router
OFF before leaving the router table for any reason.

26. If ANY of the parts is missing, DO NOT attempt
to assemble, install, or use your router table until the

missing parts have been found or replaced and your
router table has been properly and correctly assem­
bled per this manual.

27.

A

d

ANGER

Never use the floor stand as a

ladder and DO NOT stand on the router table.

INTRODUCTION

Your Craftsman Router Table comes with the following:
• A unique 4" high unitized fence with fence guides that
provide parallel movement.
• Rulers molded into the table top that provide fast
and accurate fence adjustment for making the
following items:

- Tenons
- Sliding dovetail joints
- Tongue & groove joints
- Face cuts

• The unique fence also allows you to perform these
additional routing operations:

- Veining
- Fluting
- Making crown molding
- Making cuts up to 2-1/2" from the edge of the

workpiece toward the center of the workpiece

• A specially designed push block with a quick clamp
that can clamp work pieces up to 4" wide, for end grain
or edge routing.
• An accurate jointing fence that is quickly adjustable to
the proper depth of cut.
• A dust collector port on the fence to which most 2-1/2"
wet/dry vac hoses can be attached.

OPTIONAL ROUTER TABLE ACCESSORIES

9-26478 Craftsman Router Table Floor Stand,
places router table at a convenient working height,
has adjustable floor levelers, and two steel shelves
for storage.

9-25468 Craftsman Guide Master Router Table Push
Shoe, aids in push shoe and hold down operations,
accurate measurement and router table set-up,
transforms into a miter gauge, and gives quick set-up
for 1/2" sliding dovetail joints.

9-25333 Craftsman Industrial Router Adapter Plate,
for mounting non-Craftsman 1/4" and 1/2" routers to

the router table. The holes for mounting the router

must be located and drilled by the user. The fasteners

for mounting the router to the adapter plate are not

included and must be obtained separately.

9-26478 Craftsman Router Table Floor Stand,
places router table at a convenient working height,
has adjustable floor levelers, and two steel shelves
for storage.

UNPACKING AND CHECKING CONTENTS

Refer to Parts

A

warning

If

any

of the parts is missing,

DO NOT attempt to assembie, instaii, or use your
router table until the missing parts have been

found or repiaced, and your router table has been
properly and correctly assembled per this manual.
• Contact your local Sears Retail Outlet for missing or

replacement parts.

List on page 19.

• In order to simplify handling and to minimize any
damage that may occur during shipping, your router
table comes unassembled.
• Separate all parts from the packaging materials and
check each part against the illustrations and
the parts list at the end of this manual, to make
sure that all parts have been included. Do this before
discarding any of the packaging material.