Sears 315.10186 - Manual (Page 5)

SAFETY INSTRUCTIONS FOR CHARGER
V WARNING! READ AND UNDERSTAND ALL
^ INSTRUCTIONS. Failure to follow all Instructions
listed below, may result In electric shock, fire and/or
serious personal injury.
Before using badery charger, read all Instructions and
cautionary markings In this manual, on battery charger,
battery, and product using battery to prevent misuse of
the products and possible injury or damage.
CAUTION: To reduce the risk of electric shock or
damage to the charger and battery, charge only nickel­
cadmium rechargeable batteries as specifically
designated on your charger. Other types of batteries
may burst, cetuslng personal Injury or damage.
Never use a battery that has been dropped or received
a sharp blow. A damaged battery Is subjetl to
explosion. Properly dispose of a dropped or damaged
battery immediately.
Do not expose charger to wet or damp conditions.
Water entering charger will Increase the risk of electric
shock.
Do not use any attachment or accessory not
recommended by the battery charger manufacturer.
Attachments and accessories that may be suitable for
one tool may become hazardous when used on
another tool.
Do not abuse cord or charger. Never use the cord to
cany the charger. Do not pull the charger cord rather
than the plug when disconnecting from receptacle.
Damage to the cord or charger could occur and create
an electric shock hazard. Replace damaged cords
immediately.
Make sure cord is located so that It will not be stepped
on, tripped over, come in contact with sharp edges or
moving parts or otherwise sut^ected to damage or
stress. This will reduce the risk of acddertal falls,
whl(^ could cause injury, and damage to the cord,
which could result In electric shock.
Keep cord and charger from heat to prevent damage to
housing or internal parts.
Do not let gasoline, oils, petroleum-based products,
etc. come in contact with plastic parts. They contain
chemicals that can damage, weaken, or destroy
plastic.
An extension cord should not be used unless absolutely
necessary. Usa of improper extension cord could result
in a risk of fire and electric shock. If extension cord
must be used, make sure:
a. That pins on plug at extension cord are the
same number, size and shape as those of
plug on charger.
b. That extension cord is property wired and in
good electrical condition; and
c. Thai wire size is iarge enough lor AC ampere
rating of charger as specified below:
Cord Length (Feet) 25’ 50' 100’
Cord Size (AWG) 16 16 16
Note: AWG = American Wire Gage
Do not operate charger with a damciged cord or plug,
which could cause shorting and electric shock. If
damaged, have the charger replaced by an authorized
sen/iceman.
Do not operate charger If t has received a sharp blow,
been dropped, or otherwise damaged In any way. Take
It to an authorized senriceman for electrical check to
determine If the charger Is In good working order.
Do not disassemble charger. Take I: to an authorized
serviceman when service or repair is required.
Incorrect reassembly may result In a risk of electric
shock or fire.
Unplug charger from outlet before attempting any
maintenance or cleaning to reduce the risk of electric
shock.
Disconnect charger from the power supply when not in
use. This will reduce the risk of electric shock or
damage to the charger If metal items should fall Into
the opening. It also will help prevent damage to the
charger during a power surge.
Save these Instructions.Refer to them frequently and
use them to Instruct others who may use this tool. If
you loan someone this tool, loan them these
Instructions also to prevent misuse of the product and
possible Injury.
^ WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities
contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these
chemicals are:
• lead from lead-based paints,
■ crystalline silica from bricks and cement and crlher masonry products, and
• arsenic and chromium from chemically-lrealed lumber.
Your riskf rom these exposures varies, depending on how often you do this type of work. To reduce yourexposure to these
chemicals; work
In a well ventilated area, and work approved safety equipment, such as those dust masks that are
specially designed to fitter out microscopic particles.
SAVE THESE INSTRUCTIONS