Wilkerson F34 - Manual

PRESS
TURN
COVER
ASSEMBLY
NNR
O-RING
FILTER KIT
(includes O-Ring)
BAFFLE
NNR
DRAIN ASSEMBLY
(see 9SM-96-487
for parts detail)
TRANSPARENT
PLASTIC BOWL
METAL BOWL
ASSEMBLY BOWL GUARD
METAL BOWL
ASSEMBLY
WARNING
DO NOT PLACE PLASTIC BOWL UNIT IN SERVICE
WITHOUT METAL BOWL GUARD INSTALLED
Plastic bowl units are sold only with metal bowl guards. To minimize the danger of flying fragments in the
event of plastic bowl failure, the metal bowl guards should not be removed. If the unit is in service without
the metal bowl guard installed, manufacturer's warranties are void, and the manufacturer assumes no
responsibility for any resulting loss.
IF UNIT HAS BEEN IN SERVICE AND DOES NOT HAVE A METAL BOWL GUARD, ORDER ONE AND
INSTALL BEFORE PLACING BACK IN SERVICE..
For information on materials harmful to plastic bowls, contact a Mobay Chemical or General Electric office for
information regarding materials that will attack polycarbonate plastic.
CAUTION
Certain compressor oils, chemicals, household cleaners, solvents, paints and fumes will attack plastic
bowls and can cause bowl failure. Do not use near these materials. When bowl becomes dirty replace bowl
or wipe only with clean, dry cloth. Reinstall metal bowl guard or buy and install a metal bowl guard.
Immediately replace any crazed, cracked, damaged or deteriorated plastic bowl with a metal bowl or a new
plastic bowl and metal bowl guard.
EXCEPT as otherwise specified by the manufacturer, this product is specifically designed for
compressed air service, and use with any other fluid (liquid or gas) is a misapplication. For example,
use with or injection of certain hazardous liquids or gases in the system (such as alcohol or liquid
petroleum gas) could be harmful to the unit or result in a combustible condition or hazardous external
leakage. Manufacturer's warranties are void in the event of misapplication, and manufacturer assumes
no responsibility for any resulting loss. Before using with fluids other than air, or for non-industrial
applications,or for life support systems consult manufacturer for written approval.
INSTALLATION
1.Refer to the above warning before installing filter.
2.Install as close as possible to the point where air is being used.
3.Install unit with air flowing through the body in the direction indicated by
arrow.
4.Install the same size unit as the pipe line in use. Avoid using fittings,
couplings, etc. that restrict the airflow.
5.DO NOT install filter where pressure drop could exceed 20 psi. Downstream
from a quick-opening valve, for example, could cause a momentary pressure
drop in excess of 20 psi.
6.A drain line with 1/8"-inch NPT connect may be attached to drain port if
desired. Drain line should be 1/4-inch tubing or larger; as short as possible;
and crimp free.
7.Maximum pressure and temperature ratings are: transparent plastic bowls,
150 psig (10,3 bar) and 125°F (52°C); metal bowls, 200 psig (14 bar) and
175°F (79,4°C).
8.Mount unit in vertical position.
MAINTENANCE
1.EACH TIME BOWL IS CLEANED OR THE FILTER ELEMENT REPLACED:
a. Depressurize unit.
b. Inspect seals and replace crazed, cracked, damaged or deteriorated seals
with original manufacturer's approved seals only.
2.FILTER ELEMENT-Clean periodically by removing filter, tapping on hard
surface and blowing off with an air blow gun. When cleaning or replacing
element, blow off louvers with an air blow gun.
3.Before placing the unit in service be sure that the bowl and bowl guard are
reinstalled and the4e clamp ring is securely locked in position.
4.If automatic bowl drain fails to function properly refer to Service Manual Sheet
9SM-96-487.
REPAIR KITS AND REPLACEMENT PARTS
Repair Kit (Type A Element) .............................................................FRP-95-209
Float Drain Assembly .......................................................................FRP-96-487
Metal Bowl w/Drain Seat ..................................................................GRP-95-903
Plastic Bowl w/Drain Seat & Bowl Guard .........................................GRP-95-902
Bowl Guard ......................................................................................DRP-95-810
83-281-000 REV REL 8/95
Printed in the U.S.A.
NNR=NOT NORMALLY REPLACED
INSTALLATION AND
MAINTENANCE SHEET
Filter Model F34
with Variations and Accessories
®