Oberon 1078-AP225 - Manual

Installation Instructions
Model Number 1078-AP225
(877) 867-2312 • www.oberonwireless.com
Rev. A1 03/28/14 Oberon, Inc. •••• 1315 South Allen Street •••• State College, PA 16801 Copyright 2013
Figure 1 - Cutout Dimensions
Wall Bridge In Mounting Position
Figure 5 - Installation Into Wall/Ceiling
This product is Listed by Underwriters
Laboratories Inc. Representative
samples of this product have been
evaluated by UL and meet applicable
safety standards.
File #E348543
Figure 6 - Locked Position
Model 1078-AP225 Locking Recess Wall/Ceiling Mount Assembly Components:
- Ceiling enclosure Model 1078-AP225 assembly – 1 each
- Wall bridge – 2 each
- #8-32 X 3/8 “ screw – 4 each
- #8-32 nut – 4 each
- 3/4” Trade size conduit connector – 1 each
- Fire block foam – 1 each
- Keys for access door lock – 2 each
- Installation instructions – 1 each
- Eyebolt – 4 each
- Support wire – 4 each
If any of these items are missing, contact your Oberon representative.
Find a flat work surface to assemble the enclosure, access point and antenna(s) (if
needed) prior to mounting in wall or ceiling.
Step 1 - Cut a 13” horizontal x 13.4” vertical opening in the "hard lid" ceiling or wall
(special
cutting tools may be required – ref. Figure 1).
Step 2 – Place the enclosure assembly on the work surface. Remove one of the 1”
trade size hole cover on the side of the enclosure and install the 1” trade size
conduit connector (the side on which the trade size cable clamp is to be installed
will be determined by the location the enclosure is to be installed and direction from
which conduit will be brought into the enclosure)
Step 3 – Snap Aruba Networks t-bar
clip onto the t-bar mount by angling at
a 45° angle and twisting the clip until it
snaps in place. Next, attach the
access point to the Aruba Networks t-
bar clip by angling the access point at
a 45° angle and twisting it until it also
snaps in place (Figure 2).
Step 4 – Align the threaded studs to the two outer holes in the bracket attached to the door. Once the access point is snug in
the hole, place the lock washer and wing nut onto the threaded rod. Tighten wing nuts until they are snug. With your fingers,
tighten the hex nuts on the underside of the bracket then re-tighten the wing nuts until they no longer move freely (Figure 3).
Page 2
Step 5 – For added security, attach wire ties to the two inner holes of the bracket and the t-bar mount. Make sure securely
fasten the wire ties in place (Figure 4).
Step 6 – Place the (2) two wall bridges in the mounting
position by loosing the (4) four wing nuts inside of the
enclosure. The position of the wall bridges will look like the
image in Figure 5. Place the enclosure in to the hole that
was cut in Figure 1. Angle the enclosure at 10° with the
wall bridges extended towards the bottom. The wall
bridges will go in first. Once the bottom of the enclosure is
in the hole push the enclosure so it is flush with the wall or
ceiling.
Step 7 – Once the enclosure is flush with the wall or
ceiling, slide the wall bridges in the L-slot, and draw the
bridges against the wall. Tighten the wing nuts one side at
a time (Figure 6). At this point, the enclosure is ready to be
"mudded" into the wall. Additional material my be needed.
Page 3
Figure 2 - T-Bar Clip Install
Figure 3 - T-Bar Bracket Install
Figure 4 - Attaching Wire Ties