Intex CS7111 Krystal Clear Saltwater System 2013 - Manual (Page 28)

(189PO) MODEL CS7111 SALTWATER SYSTEM & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 07/31/2012
189
PO
SAVE THESE INSTRUCTIONS
Page 28
English
TROUBLESHOOTING GUIDE
TROUBLESHOOTING
GUIDE
• The motor is not plugged in.
• Switch is not turn on.
• The GFCI circuit breaker is
tripped.
• Motor too hot and overload
protection is shut off.
• Improper sanitizer or pH levels.
• Filter cartridge is dirty.
• Damaged cartridge.
• Excessively dirty pool.
• The strainer screen is
restricting the water flow.
• Clogged inlet or discharge.
• An air leak on the intake line.
• Scale or buildup on cartridge.
• Excessively dirty pool.
• Dirty filter cartridge.
• The vacuum release valve
on the plunger valve is
activated.
• The vacuum release valve
on the plunger valve is
leaking.
• Low water level.
• Strainer screen plugged up.
• An air leak on the intake hose.
• An air lock inside the cartridge
chamber and motor chamber.
• Service light on.
• O-ring missing.
• Cover is not tight.
• Filter cartridge is dirty.
• Hose nuts are not well-fitted.
• There’s air trapped in the pump
housing and inlet hose.
• The inlet and outlet hoses
connection are reversed.
PROBLEM CAUSE SOLUTION
FILTER MOTOR
FAILS TO START
FILTER DOESN’T
CLEAN POOL
FILTER DOESN'T
PUMP WATER OR
FLOW IS VERY
SLOW
PUMP DOESN'T
WORK
TOP COVER
LEAKING
HOSE LEAKING
AIR LOCK
• Filter cord must be plugged into a 3 wire
outlet that is protected by a Class A
Ground Fault Circuit Interrupter, or RCD.
• Reset circuit breaker. If circuit breaker
trips repeatedly, your electrical system
may have a defect. Turn off circuit
breaker and call an electrician to
correct the problem.
• Let motor cool down.
• Adjust the sanitizer and pH level. Consult
your local swimming pool supply stores.
• Clean or replace cartridge.
• Check the cartridge for holes. Replace
if damaged.
• Operate the filter for longer periods.
• Clean the strainer screen at the inlet.
• Clear any obstructions in the intake
hose by discharging it inside pool wall.
• Tighten hose nuts, check hoses for
damage, check pool water level.
• Replace cartridge.
• Clean cartridge more often.
• Clean inside the plunger valve.
• Pull valve handle to full upright position.
• Turn off pump, clear any debris or obstruction in
the outlet, remove all air from the filter pump and
turn pump on again.
• Turn off pump, if water leaking from the vacuum
release valve, then release valve needs to be
replaced. Contact Intex Service Center
immediately to order replacement. You may cover
release valve with the cap temporarily if you
ensure that the strainer cover / strainer grid is
installed and you Do Not run the pump while
pool is occupied.
• Fill pool to correct water level.
• Clean strainer screens at pool inlet.
• Tighten hose nuts, check hose for
damage.
• Clear any sticks or leaves in the intake
hose.
• Turn and pull valve handle to full upright
position.
• Unscrew two air release valve on the
chamber to fullfill water.
• Contact Intex Service Center.
• Remove cover & check for O-ring.
• Tighten cover (Manually).
• Replace or clean cartridge.
• Tighten or reinstall hose nut.
• Open air release valves, lift and lower
the inlet hose until water starts to flow
out of the valve, then close it.
• The lower position of pool outlet
connects to filter pump water inlet. The
upper position of pool inlet connects to
filter pump water outlet.