Philips FW-C100 - Manual (Page 21)

o
CD
Discs for playback
This system can play all digital audio CD,
finalized digital audio CD-Recordable
and finalized digital audio CD-
Rewritable format discs.
(olo§(B
Loading the CD Changer
1 Press CD to select CD mode.
2 Press OPEN*CLOSE.
— The CD changer tray slides out.
3 Load a disc with the printed side up
in the right tray.
• You can load another disc in the left
tray.
• To load the third disc, press the
DISC CHANGE button.
-*■ The CD changer tray will rotate
until the empty tray is ready for
loading.
4 Press OPEN'CLOSE to close the
CD changer tray.
-*• A lit on the respective CD
numeric flag indicates that its
corresponding disc(s) is loaded in
the disc tray.
Note:
- To ensure good system performance,
wait until the CD changer completely
reads the disc(s) before proceeding.
Disc Direct Play
• You can play a disc directly by
pressing the DISC 1, DISC 2 or
DISC 3 button.The CD player will
stop at the end of playback of the
selected disc.
-*■ The corresponding CD numeric
flag starts to flash.
Playing a Disc
1 Press ► to start playback
-*■ A flashing on the CD numeric flag
indicates the selected disc.
The track number and elapsed
playing time of the current track
appear on the display.
• To interrupt playback press II.
The playing time flashes.
• To resume playback press ► again.
2 To stop playback press ■.
Note:
- All the available discs will play once,
then stop.
Disc Change
You can change the outer two discs
while the third inner disc is stopped or
is playing.
1 Press DISC CHANGE.
-*■ The CD changer tray slides out.
2 Replace the discs in the left and right
disc trays.
• If you wish to change the inner disc
during playback press DISC
CHANGE again.
- "SI5C CHRWGE" will be
displayed.
— The disc will stop playing.
The CD changer tray will close to
retrieve the inner disc and then
open again with the inner disc
accessible.
3 Press OPEN'CLOSE to close the
CD changer tray.
Selecting a desired track
Selecting a desired track when
piayback is stopped
1 Press N or N until the desired
track appears on the display.
2 Press ► to start playback
The selected track number and
elapsed playing time appear on
the display.
Selecting a desired track during
piayback
• Press N or N until the desired
track appears on the display.
The selected track number and
elapsed playing time appear on
the display.
• If you press N once it will skip to
the beginning of the current track
and play the track again.
Note:
- Pressing M during shuffling can only
skip to the beginning of the current
track.
Searching for a particular
passage during playback
• Press and hold or ►► until the
desired passage is located.
The volume will be reduced.
• Play returns to normal when -44 or
►► is released.
Programming Tracks
Programming tracks of a loaded disc is
possible when playback is stopped.The
display will indicate the total tracks
stored in the program. Up to 40 tracks
can be stored in the memory in any
order When 40 tracks are stored and
you attempt to store another track the
display will show'TLILL”.
1 Load the desired discs in the disc
trays.
2 Press PROGRAM to start
programming.
The PROG flag starts flashing.
A flashing on the CD numeric flag
indicates the selected disc.
3 Press the CD (CD 1 *2*3) or DISC
1/2/3 button to select the disc.
4 Press N or W to select the desired
track
pg 01-28/C100/37-EnN 12/6/00, 2.07 PM 3139 115 20881 (ENG)