Philips CDC 925/20S - Manual (Page 8)

@> PROGRAMMING OTHER POSSIBILITIES
m
3
(O
STORING A PROGRAMME (PROGRAMME)
By programming the changer you can play up to 30 tracks in
any required sequence.
FULL lights up if you exceed the maximum of 30 tracks.
• In STOP mode, press P(rogramme) to open the memory.
- PROG lights up and PROGRAM starts'flashing.
• Select the number of the first required CD using DISC
SELECT or DISC (on the remote control).
• Key in the required track numbers of this CD using the 0-9
digit buttons.
- Every track number you enter in this way will be included
immediately in the programme.
- The display always shows the number of tracks in your
programme.
• If you wish to store tracks from another CD, you should first
enter the number of the CD.
• Press P(rogramme), STOP/CP or PLAY/REPLAY to quit the
PROGRAM mode.
Err will light up if you select a non-existent CD number.
CHECKING THE PROGRAMME (REVIEW)
• Press REVIEW prior to, during or after programmed play.
- All CD and track numbers appear in the programmed
sequence on the display.
Err will light up if no track numbers have yet been stored.
With REVIEW you can proceed more rapidly to the next block
of information.
PLAYING THE PROGRAMME (PLAY/REPLAY)
• Press PLAY/REPLAY.
- Playback starts with the first number of the programme.
The EDIT, P(rogramme) and C(ancel) buttons cannot be used
during programmed play; search for a particular passage is only
possible within the track being played.
ERASING A PROGRAMME (STOP/CP or OPEN/CLOSE)
• Press STOP/CP twice or, if the CD has already stopped, just
once; you can also press OPEN/CLOSE straightaway.
- The programme has now been erased.
ERASING A TRACK FROM THE PROGRAMME (CANCEL)
• Press REVIEW before or after programmed play (STOP
mode).
- All CD and TRACK numbers appear in the programmed
sequence on the display.
• Press C(ancel) as soon as the number you wish to erase
appears.
- The number has now been erased.
Err will light up if no track numbers have yet been stored and
if you have not pressed REVIEW first before cancelling.
LISTENING WITH HEADPHONES (PHONES)
• Connect headphones with a 6.3 mm jack plug to the
PHONES socket.
• The sound level is adjusted with the LEVEL control.
EDIT
The EDIT function has a recording mode (EDIT) and a play
mode (TIMER EDIT).
- In the EDIT mode you can store the recording time of the
tape in the changer memory. This will determine which
tracks fit on one side of the tape and will stop
automatically after the last track.
- In the TIMER EDIT mode you can store a required playing
time. If necessary, the CD or the programme you wish to
play will be partly repeated to fill the entered time.
NOTE!
The EDIT function cannot be used for CDs containing more
than 29 tracks. Errwill light up if a CD contains more than
29 tracks.
Recording in the EDIT mode;
• Press EDIT (in STOP mode).
- EDIT lights up and Ec//f appears in the display, followed by
C90.
• With !◄ TRACK ►! you can now select the required
recording time: C 30, C 46, C 60, C 90, CWO or Cl20.
Other recording times can be selected using the 0-9 digit keys.
- You can now record an entire CD or a programme (from one
or more CDs):
an entire CD:
• Select the number of the required CD using DISC SELECT or
DISC (on the remote control).
- Playback starts immediately Vi/ith the selected CD.
- After each track an extra pause of 4 seconds (AUTOSPACE)
will be inserted.
- AUTOSPACE lights up.
- After the last track that fits on side A of the tape, the CD
changer will go into PAUSE mode.
• Turn the tape over or select the tape travel direction for side B.
• Press PLAY/REPLAY.
- The remaining tracks w'lll now be played.
- After the last track play will stop.
- If, after the last track of the CD, there is still enough space
available on side B, then the turntable will rotate to the next
CD in the CD compartment to record some more tracks
from this CD (this will also happen if the last track has been
recorded on side A).
• Press STOP/CP if this is not required.
a programme:
• Compile your programme (from one or more CDs) as
described in the 'PROGRAMMING' section (the programme
can also be stored in advance).
• Press PLAY/REPLAY to start play.
- After each track an extra pause of 4 seconds (AUTOSPACE)
will be inserted.
- AUTOSPACE lights up.
- After the last track that fits on side A of the tape, the CD
changer will go into PAUSE mode.
• Turn the tape over or select the tape travel direction for side B.
• Press PLAY/REPLAY.
- The remaining tracks will now be played.
- After the last track play will stop.