Interlogix Simon XTi CDMA Module V4 - Manual (Page 8)

to enable Z-Wave services on the
account.
--- Add Device 2 Add Z-Wave devices to the module’s
network. Make sure the device you are
trying to add is powered up and within 3
to 6 feet of the Simon XTi panel. Read the
manufacturer’s instructions on what
button to press on the device to enroll it.
--- Remove Device 2 Remove an existing Z-Wave device, or to
“reset” a Z-Wave device that was
previously learned into a different Z-
Wave network, before you can learn it
into the CDMA module.
---Update 2WTTS Press Update 2WTTS to force an update
of the thermostat, lights or locks
information shown on the touch screen
(2WTTS). Note that these updates may
take several minutes to complete.
----Thermostats View thermostat data and
update/remove thermostats from display
on the panel and touch screens.
----Lights Update the lights list shown on the panel
and touch screens.
----Locks Update locks list shown on panel and
touch screens and pair locks with their
door contact sensor.
--- Advanced 2 Provides additional functionality for
advanced Z-Wave troubleshooting and
configuration.
---- Rediscovery 2 Network rediscovery allows the system to
determine the most efficient
communication patch between Z-Wave
devices. (During this process the Z-Wave
network is busy and cannot respond to
other commands.)
---- Replicate Mode 2 Initiates replicate mode on the panel.
---- Send Node Info 2 For advanced use only. Do not use
unless directed to do so by Alarm.com.
---- Refresh Thermostat 2 Requests updated thermostat data.
--Advanced Menu This menu houses advanced CDMA
module tasks.
---Auth. Code Requests an authorization code from
Alarm.com for use on the Image Sensor
Installer Test Site
(www.alarm.com/imagesetup).
---Create Account This menu is available only to installers
who have their own Alarm.com account
creation system. You must enter a
Technician ID and a Lead ID in order to
use this menu.
System Programming +
Master Code
Scroll to Programming. Enter the
Master Code
- Interactive Services Select Interactive Services.
-- Module Status Provides status and troubleshooting
information for the CDMA module.
-- Image Sensor This menu is used to view the status of
and test Image Sensors. This menu can
also be used to retrieve images from the
enrolled Image Sensors.
---Status View signal strength, PIR, battery and
other information about each Image
Sensor enrolled.
---Privacy Clear all Image Sensor images currently
stored on the XTi panel. (This does not
affect image storage on the Alarm.com
online account.)
---Image List View list of images captured by the
Image Sensor(s) on the system and
request to have specific images sent to
the panel for local viewing.
--- Test Put the Image Sensor in PIR Test Mode
(LED on sensor illuminates when
activated) or request an “Installer Peek-In
Now” to test image captures.
-- Weather Update Request a Weather Update if the weather
forecast is not showing on the XTi touch
screen. To speed up the process, stay in
Programming. This keeps the panel in
high-speed communication mode with
the touch screens.
-- Z-Wave 2 Used to add, remove, and troubleshoot Z-
Wave devices and networks. To control Z-
Wave devices via the Alarm.com website
and smart phone apps, you will also need
to enable Z-Wave services on the
account.
--- Add Device 2 Add Z-Wave devices to the module’s
network. Make sure the device you are
trying to add is powered up and within 3
to 6 feet of the Simon XTi panel. Read the
manufacturer’s instructions on what
button to press on the device to enroll it.
--- Remove Device 2 Remove an existing Z-Wave device, or to
“reset” a Z-Wave device that was
previously learned into a different Z-
Wave network, before you can learn it
into the CDMA module.
---Update 2WTTS Press Update 2WTTS to force an update
of the thermostat, lights or locks
information shown on the touch screen
(2WTTS). Note that these updates may
take several minutes to complete.
----Thermostats View thermostat data and
update/remove thermostats from display
on the panel and touch screens.
----Lights Update the lights list shown on the panel
and touch screens.
----Locks Update locks list shown on panel and
touch screens and pair locks with their
door contact sensor.
--- Advanced 2 Provides additional functionality for
advanced Z-Wave troubleshooting and
configuration.
---- Rediscovery 2 Network rediscovery allows the system to
determine the most efficient
communication patch between Z-Wave
devices. (During this process the Z-Wave
network is busy and cannot respond to
8 Simon XT/XTi CDMA Module V4 Installation Instructions