Interlogix 600-1053-4 - Manual (Page 8)

8 600-1053-4 Concord 4 CDMA Module Installation Sheet
at a thermostat) to verify that it is successfully communicating
with the Alarm.com module.
If you are onsite at the customer location and do not have
access to the website, you can also check communication
using the Z-Wave LED L2. When the Alarm.com module is in
Normal mode it is by default off, but issues a single flash
whenever it receives a message from a device in its own Z-
Wave network. if a device is next to the panel, you can use this
feature to test whether or not the device is currently installed
on the Alarm.com Z-Wave network, and whether or not it is
communicating properly.
To check communication between a Z-Wave device and
the Alarm.com module:
1. Ensure that the Z-Wave device is powered on, and then
press the same button you would use if you were trying to
add it to a network (check the device’s installation
instructions if you are unsure which button to press).
2. The LED L2 on the module will issue a quick single flash
to indicate it has heard the signal form the device. If
theLED L2
does not flash when the device’s button is
pressed, this is most likely because of one of the following:
a) the device is not in the Alarm.com module’s Z-Wave
network; b) it is out of direct communication range form
the Alarm.com module; or c) the device is not powered on
or working properly.
Deleting a Z-Wave device (Device Exclusion)
You can enter Delete mode to:
• Delete a Z- Wave device from the Alarm.com module’s Z-
Wave network if you no longer want the device in the
network (e.g., if it is no longer in use).
• Delete a Z-Wave device from a different network so that it
can then be added into the Alarm.com network. (A given
Z-Wave device and only be assigned to one Z-Wave
network at a time. If it is already assigned to one network,
it needs to be deleted from one network before it can be
added to another network.)
Whether you are deleting a device from the Alarm.com
module’s Z-Wave network or another Z-Wave network, the
steps are the same.
1. Put the Alarm.com module into Z-Wave Add mode.
On the Alarm.com module, press and hold down the Z-
Wave Mode button to enter Add mode (4-blink pattern on
the LED L2). Once in Add mode, press and hold down the
Z-Wave Mode button again until the LED L2 begins
flashing a 2-blink pattern to indicate Z-Wave Delete mode.
(See Figure 2 on page 7 for illustration of how to press the
button.)
2. Press buttons on the Z-Wave device to delete.
Once the module (or controller) is in Z-Wave Delete mode,
press the appropriate buttons on the Z-Wave device to
delete it from the network. See Device-specific instructions
(or the instructions that came with the device) for more
information.
3. Confirm the Z-Wave device was deleted successfully.
4. Once the device has been deleted successfully, the panel
will beep, and the yellow LED L2 on the Alarm.com
module’s Z-Wave board will become solid and stay solid
for 1 minute (allow up to 5 seconds for confirmation once
the device has been triggered).
If a device is not longer functioning, you can also delete it
through the Device Automation page on the Alarm.com Dealer
website. Send a remote command to the device and wait a few
minutes for the command to register as failed. The failed
device will have a remote node link next to it.
emPower on the Alarm.com Dealer website
Through the Alarm.com Dealer Website you can modify the
emPower service plan, view the Z-Wave device list, and order
emPower modules and devices. To add or remove emPower
features from your customer’s service plan, go to the
customer’s service plan page and check the features (lights,
locks, thermostat, or the energy package - lights and
thermostat) that you would like to add/remove. To view a list of
your customer’s Z-Wave devices, pull up their account and
click the “emPower Devices” link.
Device-specific instructions
Controllers
Advanced Remote Controller
Note: if a controller will be used with the system, Alarm.com
recommends adding it before the rest of the Z-Wave devices.
Refer to the instructions that came with your controller for more
information on controller features and operation.
To add the controller to the security panel (system):
1. Enter your panel into Add mode.
2. With the controller close to your panel, press and hold the
Setup button on the controller until the controller screen
displays “Lights Setup”.
3. Use the arrow buttons to scro ll until you see “Transfer” on
the controller screen. Press the OK button.
4. The controller screen should now display “Primary”. Use
the arrow buttons to scroll until you see “Receive”.
5. Press the OK button. The controller screen should display
“Receiving”.
6. The controller screen will briefly display “Success” after
the controller has been successfully included into the
panel.
To add a light module to the system using the controller:
1. Press and hold the Setup button on the controller until the
screen displays “Light Setup”. Press the OK button.
2. The controller screen should now display “Add”. Press the
OK button.
3. The controller screen should now disp lay “To Network”.
4. Use the arrow buttons to scroll until you see “To a Key”
and then press the OK button.
5. Press a number key 1 to 9 or Setup (Shift) and a number
key for numbers 10 to 18.
6. Press the OK button and the screen should now display
“Setup Waiting”.