Great Planes Reactor 3D EP ARF - GPMA1540 - Manual (Page 4)

• Great Planes LiPo 1250mAh 11.1V 20C Discharge
w/Balance (GPMP0609)
• Great Planes LiPo 1500mAh 11.1V 20C Discharge
w/Balance (GPMP0613)
• Great Planes LiPo 2100mAh 11.1V 20C Discharge
w/Balance (GPMP0617)
Note: Do not use Great Planes LiPo 1500mAh 11.1V 3S 8C
Discharge (GPMP0831). This battery pack is not capable of
supporting the current draw of the recommended
power systems.
This is the list of adhesive and building supplies required to
finish the Reactor 3D EP ARF. Order numbers are provided
in parentheses.
❏
1/2 oz. [15g] Thin Pro ™ CA (GPMR6001)
❏
1/2 oz. [15g] Medium Pro CA+ (GPMR6007)
❏
Pro 30-minute epoxy (GPMR6047)
❏
Denatured alcohol
❏
Drill bits: 5/64" [2mm], #54 (.0550")
❏
#1 Hobby knife (HCAR0105)
❏
#11 Blades (5-pack, HCAR0211)
❏
Hobbico ® steel T-pins 1" [25mm] (100, HCAR5100)
Here is a list of optional supplies and tools mentioned in the
manual that will help you build the Reactor 3D EP ARF.
❏
1" [25mm] Double-sided foam mounting
tape (GPMQ4442)
❏
21st Century ® sealing iron (COVR2700)
❏
21st Century iron cover (COVR2702)
❏
2 oz. [57g] Spray CA activator (GPMR6035)
❏
4 oz. [113g] Aerosol CA activator (GPMR634)
❏
CA applicator tips (HCAR3780)
❏
CA debonder (GPMR6039)
❏
Epoxy brushes (6, GPMR8060)
❏
Mixing sticks (50, GPMR8055)
❏
Mixing cups (GPMR8056)
❏
Hobbico Duster ™ can of compressed air (HCAR5500)
❏
K & S #801 Kevlar ® thread (for stab
alignment, K+SR4575)
❏
Panel line pen (TOPQ2510)
❏
Rotary tool such as Dremel ®
❏
AccuThrow ™ deflection gauge (GPMR2405)
❏
Hobbico flexible 18" ruler stainless steel (HCAR0460)
• When you see the term test fit in the instructions, it
means that you should first position the part on the
assembly without using any glue, then slightly modify or
custom fit the part as necessary for the best fit.
• Whenever the term glue is written you should rely upon
your experience to decide what type of glue to use. When a
specific type of adhesive works best for that step, the
instructions will make a recommendation.
• Whenever just epoxy is specified you may use either
30-minute (or 45-minute) epoxy or 6-minute epoxy. When
30-minute epoxy is specified it is highly recommended that
you use only 30-minute (or 45-minute) epoxy, because you
will need the working time and/or the additional strength.
• Photos and sketches are placed before the step they
refer to. Frequently you can study photos in following steps
to get another view of the same parts.
• The stabilizer and wing incidences and engine thrust
angles have been factory-built into this model. However,
some technically-minded modelers may wish to check these
measurements anyway. To view this information visit the web
site at www.greatplanes.com and click on “Technical Data.”
Due to manufacturing tolerances which will have little or no
effect on the way your model will fly, please expect slight
deviations between your model and the published values.
Replacement parts for the Great Planes Reactor 3D EP
ARF are available using the order numbers in the
Replacement Parts List that follows. The fastest, most
economical service can be provided by your hobby dealer or
mail-order company.
To locate a hobby dealer, visit the Hobbico web site at
www.hobbico.com. Choose “Where to Buy” at the bottom
of the menu on the left side of the page. Follow the
instructions provided on the page to locate a U.S., Canadian
or International dealer.
Parts may also be ordered directly from Hobby Services by
calling (217) 398-0007, or via facsimile at (217) 398-7721,
but full retail prices and shipping and handling charges will
apply. Illinois and Nevada residents will also be charged
sales tax. If ordering via fax, include a Visa
® or MasterCard ®
number and expiration date for payment.
Mail parts orders and payments by personal check to:
Hobby Services
3002 N. Apollo Drive, Suite 1
Champaign, IL 61822
ORDERING REPLACEMENT PARTS
IMPORTANT BUILDING NOTES
Optional Supplies & Tools
Required Adhesive & Building Supplies
4