Great Planes Piper J-3 Cub 60 Kit - GPMA0162 - Manual (Page 4)

D Four-channel radio with 5 servos
D "Y" Harness (Futaba J HCAM2500, Airtronics
HCAM2520, JR HCAM2530)*
-or-
D Dual Servo Extension (Futaba J FUTM4130)
D 6" Servo extension cords (3) (Futaba J HCAM2000,
Airtronics HCAM2020, JR HCAM2030)
D Propellers (see engine instructions for
recommended size)
D 12 to 16 oz Fuel Tank (12 oz. GPMQ4105, 14 oz.
GPMQ4106, 16 oz GPMQ4107)
D 1-1/2" Tail Wheel (GPMQ4243)
D 4" Cub Wheels (GPMQ4230 3-3/8" Piper Cub
Wheels suitable)
D 3/16" Wheel Collars (4) (GPMQ4308, pkg of 4)
D 3/32' Wheel Collars (2) (GPMQ4302, pkg of 4)
D 3/16" Bolt on Axle Shafts (GPMQ4278)
D 25 foot roll model covering (Top Flite Cub Yellow
MonoKote Covering TOPQ1220)
D 1/8" black striping tape (GPMQ1480)
D Medium silicone Fuel Tubing (GPMQ4131)
D 1/2" thick Latex Foam Rubber Padding (HCAQ1050)
D Flexible Cable throttle pushrod (opt'l) (GPMQ3700)
D Screw-Lock Pushrod Connectors (opt'l) (GPMQ3870)
D Switch & Charge Jack Mount (optional) (GPMM1000)
D Fuel filter (optional) (GPMQ4150)
D Fueling Valve (GPMQ4160)
D Fuelproof paint (see "Painting" section of instructions
on page 44)
D 3" scale pilot (optional) - (Williams Bros. WBRQ2626)
*ltems in parenthesis (GPMQ4130) are suggested part
numbers recognized by distributors and hobby shops and
are listed for your convenience Our own brand has been
provided where possible GPM is the Great Planes brand,
HCA is the Hobbico brand, TOP is Top Flite
D 2 oz Thin CA Adhesive - (GPMR6015)
D 2 oz Medium CA Adhesive - (GPMR6009)
D 2 oz Thick CA Adhesive - (GPMR6003)
D CA accelerator (optional) - (HCAR3750)
D CA applicator tips (optional) - (HCAR3780)
D 6-Minute Epoxy - (GPMR6045)
D 30-Minute Epoxy - (GPMR6047)
D Pacer Z-560 (optional) - for gluing windscreen and
side windows (PAAR3300)
D Silver Solder (recommended) - (GPMR8070 w/flux)
D Hand or Electric Drill
D Drill Bits 1/16", 3/32", 7/64" or #35, 1/8", #29 or 9/64",
11/64", 3/16", #10 or 13/64", 7/32", 15/64", 17/64" and
1/4"
D Sealing Iron - (TOPR2100)
D Hot Sock (optional) - (TOPR2175)
D Heat Gun (optional) - (TOPR2000)
D Razor Saw
D #1 knife handle - (XACR4305)
D #11 Blades - (XACR3121 pkg of 5)
D Common pliers
D Screwdrivers (phillips and flat)
D T-Pins - (HCAR5100 small, HCAR5150 medium,
HCAR5200 large)
D Straightedge - (Fourmost Non Slip FORR2149)
D Masking Tape
D Sandpaper (coarse, medium, fine grit)
D T-Bar or sanding block
D Waxed Paper
D Lightweight Balsa Filler - (HCAR3401)
D 5/32" brass tube (optional)
D 1/8" brass tube (optional)
D Tap Wrench
D 1/4-20 Tap - (GPMR8105 w/dnll bit)
D 8-32 tap - (GPMR8103 w/dnll bit)
D 6-32 tap - (GPMR8102 w/dnll bit)
D IsopropyI Rubbing Alcohol (70%)
D Dremel Moto Tool or similar w/sanding drum, cutting
burr (optional)
D 9/64" ball end hex wrench - (GPMR8004)
D Kyosho" Curved Scissors (optional) - (KYOR1010)
4