Golden Lighting 8107-6 WG - Manual

Assembly Instructions: 8107-6 WG (Torbellino)
IMPORTANT:
• ALL INSTALLATION WORK SHOULD BE DONE BY ACCREDITED PROFESSIONAL.
• SHUT OFF POWER SUPPLY AT FUSE OR CIRCUIT BREAKER!
• USE ONLY THE SPECIFIED BULBS. DO NOT EXCEED THE MAXIMUM WATTAGE!
PREPARING FOR INSTALLATION
Remove all of the contents from the carton. See the
important notes above. Shut off the power at the circuit
breaker and completely remove the old fixture from the
ceiling, including the old mounting strap.
From the parts bag remove the mounting strap assembly.
One end of nipple (F) should be attached to mounting strap
(A) with hex nuts (C, D) in place. The other end should have
canopy loop (H) attached.
Mounting strap (A) contains several pairs of threaded holes.
Find the pair of holes that matches the spacing of the holes
on the junction box. Attach mounting strap (A) to the junction
box using mounting screws (B) and a screwdriver. Tighten
securely. Unscrew canopy loop collar (I) from canopy loop
(H). Pass canopy (G) over the mounted canopy loop to test
the height. Approximately half of the canopy loop exterior
threads should be exposed, and the canopy look collar
should fit snugly on the canopy loop. Remove canopy (G)
and adjust the height of nipple (F) and canopy loop (H) until
the desired height is reached.
ASSEMBLING THE FIXTURE
If the arms of the fixture are packed closed, gently spread
the arms until they are evenly spaced. Use decorative thumb
screw (R) to secure the arms to housing (Q). Place the
bottom of the fixture on a flat surface. Top loop (L) is on the
fixture wires, but not attached to the body of the fixture. Pass
the fixture wires through top loop (L). Pull the wires until taut
and thread top loop (L) onto the fixture body.
By measuring, determine the correct number of chain links
needed for proper hanging height. If necessary, use a pair
of pliers to open and remove any excess chain. Attach one
chain connector to each end of the chain. Use one of the
chain connectors to attach the chain to top loop (L) and close
the chain connector. Feed the fixture wires up through the
chain (every three links or so), pulling wires until taut. Slide
the canopy loop collar and canopy onto the chain/wire. Use
the free chain connector to attach chain to canopy loop (H).
CONNECTING THE WIRES
Have an assistant support the fixture weight while completing
the wiring. Cut away excess wire. Thread the fixture wires
through the canopy loop (H) and nipple (F). Attach the
fixture’s wire to the power supply wires from the junction
box. Connect black to black (or smooth); white to white (or
ribbed); ground to ground (green or copper). Twist the ends
of the wire pairs together, then twist on a wire connector.
Make sure all twists are in the same direction. If there is no
ground wire (green or copper) from the junction box, locate
ground screw (E) on mounting strap (A) and wrap the fixture
ground wire around the green ground screw (E). Use a
screwdriver to secure the ground screw onto the mounting
bracket. Tuck all wires neatly into the junction box.
FINISHING THE INSTALLATION
Push canopy (G) up to the ceiling and slide canopy loop
collar (I) up beneath the canopy. Thread canopy loop collar (I)
onto canopy loop (H) tightly to secure canopy (G) into place.
Slide glass shades (O) onto sockets (P) and secure the glass
in place with socket rings (N). Install bulbs (M) (not included)
in accordance with the fixture’s specifications.
Do not exceed the maximum wattage. Your installation is
now complete. Turn on the power and test the fixture.
CLEANING TIPS
Treat the fixture gently! Regular cleaning will reduce the need for deep cleaning. For regular cleaning, turn off the light and wipe down the
fixture with a clean lint-free cotton or microfiber cloth. Never spray cleaner directly onto the fixture. For deep cleaning, turn off the light
and remove the glass prior to cleaning. Hand wash glass with warm water and mild detergent. Dry with a lint-free or microfiber cloth.
A
B
C
H
I
G
J
K
E
D
F
L
M
N
O
P
R
Q
BLACK
(Hot)
WHITE
(Neutral)
GREEN
(Ground)
HOUSE WIRES
SMOOTH
(Or Black)
FIXTURE WIRES
RIBBED
(Or White)
BARE COPPER
(Or Green)
For Customer Service, contact
the place of purchase to arrange
for replacement parts.