Golden Lighting 2314-5 GR - Manual

Assembly Instructions: 2314-5 GR (Gwendolyn)
IMPORTANT:
• All InstAllAtIon work should be done by AccredIted professIonAl.
• shut off power supply At fuse or cIrcuIt breAker!
• use only the specIfIed bulbs. do not exceed the mAxImum wAttAGe!
PRePARING fOR INsTAllATION
carefully remove all of the contents from the carton. see the
important notes above. shut off the power at the circuit breaker
and completely remove the old fixture from the wall, including
the old mounting strap.
From the parts bag remove the mounting strap assembly. One
end of nipple (F) should be attached to mounting strap (A) with
hex nuts (C, D) in place. The other end should have canopy loop
(h) attached.
Attach mounting strap (A) to the junction box using mounting
screws (B) and a screwdriver. Tighten securely. Unscrew canopy
loop collar (I) from canopy loop (h). pass canopy (G) over the
mounted canopy loop to test the height. Approximately half
of the canopy loop’s exterior threads should be exposed, and
the canopy loop collar should fit snugly onto the canopy loop.
Remove canopy (G) and adjust the height of nipple (F) and
canopy loop (H) until the desired height is reached.
AsseMblING The fIxTuRe
By measuring, determine the correct length of chain needed for
proper hanging height. If necessary, use a pair of pliers to open
and remove any excess chain. Attach one of chain connectors
(K) to chain (J). Pass the fixture wires through top loop (L). Pull
the wires until taut. Attach one end of chain connector (k) to top
loop (L) and close chain connector (K). Feed the fixture wires
up through the chain (every three links or so), pulling the wires
until taut. use the free chain connector (k) to attach chain (J)
to canopy loop (h). slide canopy loop collar (h) and canopy (G)
down onto the chain/wires. pull the wires until taut. trim the
wires to the desired length plus 8 to 10 inches.
CONNeCTING The WIRes
Have an assistant support the fixture weight while completing
the wiring. Cut away excess wire. Thread the fixture wires
through canopy loop (H) and canopy (G). Attach the fixture’s
wires to the power supply wires from the junction box. Connect
black to black (or smooth); white to white (or ribbed); ground
to ground (green or copper). Twist the ends of the wire pairs
together, then twist on a wire connector. Make sure all twists are
in the same direction. If there is no ground wire (green or copper)
from the junction box, locate ground screw (E) on mounting
strap (A) and wrap the fixture ground wire around the green
ground screw (E). Use a screwdriver to secure ground screw (E)
onto the mounting bracket. Tuck all wires neatly into the junction
box.
fINIshING The INsTAllATION
Push canopy (G) up to the ceiling and slide canopy loop collar
(I) up beneath the canopy. Tightly thread canopy loop collar (I )
onto canopy loop (h) to secure canopy (G) in place.
slide candle sleeves (p) over the socket.
Install light bulbs (O) (not included) in accordance with
the fixture’s specifications. Do not exceed the maximum
recommended wattage.
Slide shade (N) over the light bulb.
Place the decorative chains (M) and (Q) onto the fixture.
your installation is now complete. turn on the power and test
the fixture.
CleANING TIPs
Treat the fixture gently! Regular cleaning will reduce the need for deep cleaning. For regular cleaning, turn off the light and wipe down the
fixture with a clean lint-free cotton or microfiber cloth. Never spray cleaner directly onto the fixture.
for Customer service, contact
the place of purchase to arrange
for replacement parts.
A
B
C
H
I
G
J
K
E
D
F
L
P
O
N
M
Q