Casio CTK-671 User Manual
Page 87
A-13
3 :
Depth(Range: -64 to 0 to +63)
Adjusts the depth of the wah in accor
dance
with the level of the input signal.
Setting a positive value causes the wah filter
to open in dir
ect pr
oportion with the size of
the input signal, pr
oducing a bright sound.
Setting a negative value causes the W
ah filter
to close in accor
dance with the size of the in-
put signal, which pr
oduces a dark tone qual-
ity
. However
, lar
ge input r
e-opens the W
ah fil-
ter
, even if it is closed.
06 :
Compressor
■
Function
Compr
esses the input signal, which can have
the ef
fect of suppr
essing level variation and
making it possible to sustain dampened
sounds longer
.
■
Parameters
0 :
Depth (Range: 0 to 127)
Adjusts compr
ession of the audio signal.
1 :
Attack (Range: 0 to 127)
Adjusts the attack amount of the input signal.
A
smaller value causes pr
ompt compr
essor
operation, which suppr
esses the attack of the
input signal.
A
lar
ger values delays compr
essor operation,
which causes attack to be output as-is.
2 :
Release (Range: 0 to 127)
Adjusts the time fr
om the point when the in-
put signal dr
ops below a certain level until the
compr
ession operation is stopped.
When an attack feeling is desir
ed (no compr
es-
sion at the onset of the sound), set this param-
eter to as low a value as possible.
T
o
have compr
ession applied at all times, set a
high value.
3 :
Level (Range: 0 to 127)
Adjusts the output level.
The output volume changes in accor
dance with
the Depth setting and the characteristics of the
input tone. Use this parameter to corr
ect for
such changes.
07 :
Limiter
■
Function
This is an ef
fector that you can use to set an
upper limit value on the level of the input sig-
nal.
■
Parameters
0 :
L
imit (Range: 0 to 127)
Adjusts the volume level fr
om which the limit
is applied.
1 :
Attack (Range: 0 to 127)
Adjusts the attack amount of the input signal.
2 :
Release (Range: 0 to 127)
Adjusts the time fr
om when the input signal
dr
ops below a certain level until the limit op-
eration stops.
3 :
Level (Range: 0 to 127)
Adjusts the level being output.
The output volume changes in accor
dance with
the Limit setting and the characteristics of the
input tone. Use this parameter to corr
ect for
such changes.
08 :
Distortion
■
Function
This ef
fect pr
ovides Distortion +
AmpSimulator
.
■
Parameters
0 :
Gain (Range: 0 to 127)
Adjusts the input gain.
1 :
Low (Range: 0 to 127)
Adjusts the low-band gain.
The cutof
f fr
equency dif
fers accor
ding to the
pr
eset DSP
.
2 :
High (Range: 0 to 127)
Adjusts the high-band gain.
The cutof
f fr
equency dif
fers accor
ding to the
pr
eset DSP
.
3 :
Level (Range: 0 to 127)
Adjusts the output level.
09 :
Stereo Phaser
■
Function
This is a ster
eo phaser that modulates the phase
in accor
dance with a sine wave LFO.
■
Parameters
0 :
Resonance (Range: 0 to 127)
Adjusts the r
esonance of the sound.
1 :
Manual (Range: -64 to 0 to +63)
Adjusts the phaser shift volume, which is used
for r
efer
ence.
2 :
Rate (Range: 0 to 127)
Adjusts the rate of the LFO.
3 :
Depth (Range: 0 to 127)
Adjusts the depth of the LFO.
4 :
W
et Level (Range: 0 to 127)
Adjusts the volume level of the ef
fect.
10 :
Phaser
■
Function
This is a monaural phaser that modulates the
phase in accor
dance with a sine wave LFO.
■
Parameters
0 :
Resonance (Range: 0 to 127)
Adjusts the r
esonance of the sound.
1 :
Manual (Range: -64 to 0 to +63)
Adjusts the phaser shift volume, which is used
for r
efer
ence.
703A-E-159A