Before setting surface controls – Kenmore ELITE 790.367 User Manual
Page 9
Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".
Figure 3
Electrodes must
align into slot or hole for each
Burner Head
9|f
9k
91=
Bridge Burner
3 positions
Jnot marked) .
Assembly of the Surface Burner Heads, Burner Caps and Burner Grates (Porcelain Cooktop
models)
It is very important to make sure that all of the Surface Burner Heads, Surface Burner Caps and Surface Burner Grates
are installed correctly and at the correct locations.
1. Remove all packing tape from cooktop area. Remove all
BurnerCapsand Burner Heads.
2. Discard all packing material located under Burner Heads (if
applicable).
3. To replace the Burner Heads & Caps, match the letters
located under center of Burner Caps with the letters located
inside BurnerHeads{Figure 1).
4. Match Burner Skirts with Burner Heads and Burner Caps (see
Figure 1). Replace the Burner Heads and Caps on cooktop
(see Figure 2). Carefully align the Electrodes into slot or hole
of each Burner Head (Figure 3). Note: The Burner Heads
should sit flat on Cooktop Burner Skirts.
5. Place the removable oven vent cover over the fixed oven
vent cover.
6. Unpack Burner Grates and position on the cooktop.
REMEMBER —
DO NOT ALLOW SPILLS, FOOD, CLEANING AGENTS OR ANY OTHER MATERIAL TO ENTER THE
GAS ORIFICE HOLDER OPENING.
Always keep the Burner Caps and Burner Heads in place whenever the surface
burners are in use.
Assembly of the Surface Burner Heads, Burner Caps and Burner Grates (Ceramic Glass
Cooktop models)
It is very important to make sure that all of the Surface Burner
Heads, Surface BurnerCapsand Surface Burner Grates are
installed correctly and at the correct locations.
1. Be sure to follow the Installation Instructions before installing
and using your new range.
2. Remove all packing tape from cooktop. Remove Burner Caps
and Burner Heads (See Figure 4).
3. Discard all packing material located under all Burner Heads (if
applicable).
4. To replace Burner Heads & Caps, match the letters located under
center of Burner Caps with the letters located inside Burner Head
(only positions A & F are marked with letters - See Figure 5).
Place all Burner Heads & Caps on the cooktop (See Figure 4)
while carefully aligning the Electrodes into slots or holes of the
Burner Heads (Figure 7). Note: The Burner Heads should sit flat
on Cooktop Burner Skirts.
5. Replace Bridge Burner Caps. These include one Bridge Burner
Center Cap (rectangular shaped) and the two Bridge Burner End
Caps (The Bridge Burner End Caps will tit either the front or rear
Bridge Burner Head locations). Make sure that the tabs located
under the Bridge Burner Caps fail into the slots located in the
Bridge Burner Head (See arrows in Figure 6) and that all the Bridge
Burner Caps lie flat and evenly on the Bridge Burner Head.
6. Unpack Burner Grates. NOTE: Do not force End Burner Grates
down on cooktop. Be careful to line up the 2 Grate Pins located
on each of the 2 End Burner Grates into the Pilot holes located
on top of the Burner Caps (See Figure 8). Position Burner
Grates on cooktop and check that all the Burner Grate legs lie
on the glass surface.
7. Place Center Burner Grate between the end Burner Grates.
REMEMBER —
DO NOT ALLOW SPILLS, FOOD, CLEANING AGENTS OR ANY OTHER MATERIAL TO ENTER THE
GAS ORIFICE HOLDER OPENING.
Always keep the BurnerCapsand Burner Heads in place whenever the surface
burners are in use.
9
Before Setting Surface Controls
7 ■ Burner
.... . . Cap ,
N
m \
Figure 4
Bridge Burner Head
Bridge
Burner
4-End
Cap
Bridge
, Burner
Center
Cap
Bridge
Burner
■End
Cap
Burner,'
Head ■
Figures
Electrodes
must align into slot or hole
tor each Burher Head
Figure 7
Figures
Grate Pin
Burner
Cap
Pilot hole
f.. (
Figures