Programming the universal, Remote control (forct-3268s) cable box, Remote control – Panasonic CT-3268S User Manual
Page 28: Forct-3268s) cable box, Preferred procedure, Aiternate procedure, I ffl. i, L el
Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".

Programming The Universal
VCR
Preferred Procedure
-
Code Known
Programming Universal Remote Using
Infrared Access Codes for VCRs
• Determine brand of VCR.
• Identify code(s) associated with the brand in the
infrared code index for VCRs (located in this manual).
Procedure
TV/VCR/CABLE
1. Place the Remote
CUD
into the VCR position.
VCR POWER
2. Press and hold
Remote.
down on Universal
3.
Enter two digit code using keypad “0 through 9”
buttons.
VCR POWER
Release
The Universal Remote is now
programmed.
NOTE:
Some brands have multiple codes. Repeat
procedure using each code listed until VCR
responds correctly,
Aiternate Procedure
-
Code Unknown
Programming Universal Remote Using the
“Sequence Method” for VCRs
• Confirm VCR is plugged in and operating properly, then
turn OFF.
Procedure
TV/VCR/CABLE
1. Place the Remote
I ffl. I
into the VCR position.
VCR POWER
2. Press and hold the
Remote.
down on Universal
3.
Press ^ repeatedly. Check for the VCR to turn ON
after each press. When the VCR turns ON, release
VCR Power button. The proper infrared code has now
been accessed.
NOTES:
1. It may take several attempts before the correct code is
found.
2.
The can be used to return to a code that was
accidently passed by.
3.
Some Remote Controls may have unique operating
functions for some buttons. For Example: The
POWER button may only turn the VCR OFF as
opposed to both ON and OFF. It will then be necessary
to modify the procedure. Turn the VCR ON and
repeatedly press the ^ until the VCR turns OFF.
Remote Control
(forCT-3268S)
Cable Box
Preferred Procedure - Code Known
Programming Universal Remote Using
Infrared Access Codes for Cable Boxes
• Determine brand of Cable box.
•
Identify code(s) associated with the brand in the
infrared code index for Cable boxes (located in this
manual).
Procedure
TV/yCR/CABLE
1.
Place
the
Remote
(—El
into
the
CABLE
position.
CABLE
POWER
2. Press and hold the
down on Universal
Remote.
3.
Enter two digit code using keypad "0 through 9”
buttons.
CABLE
POWER
Release □ The Universal Remote is now
programmed.
Use the Remote ^ and ^ for
selecting Cable Box channels.
NOTE:
Some brands have multiple codes. Repeat
procedure using each code listed until Cable box
responds correctly.
Aiternate Procedure - Code Unknown
Programming Universal Remote Using the
“Sequence Method” for Cable Boxes
• Confirm Cable box is plugged in and operating properly,
then turn OFF.
Procedure
TV/VCWCABLE
1
.
Place the Remote
L El
into the CABLE
position.
CABLE
POWER
2. Press and hold CZl down on Universal Remote.
3.
Press ^ repeatedly. Check for the Cable box to turn
ON after each press. When the Cable box turns ON,
release Cable Power button. The proper infrared
code has now been accessed.
NOTES:
• It may take several attempts before the correct code is
found.
• The ^ can be used to return to a code that was
accidently passed by.
• Some Remote Controls may have unique operating
functions for some buttons. For Example: The POWER
button may only turn the Cable box OFF as opposed to
both ON and OFF. It will then be necessary to modify the
procedure. Turn the Cable box ON and repeatedly
press the^ until the Cable box turns OFF.
NOTE:
When operating equipment (VCR or Cable box) with the Universal Remote Control, the TVA/CR/CABLE Switch
should be set to the same position where the Access Code was first programmed for the equipment. Otherwise,
leave the switch in the TV position.
- 2 8 -