Kontron CP6003-RC IPMI User Manual

User guide, Cp6003-sa/ra/rc ipmi firmware

If it’s embedded, it’s Kontron.

» User Guide «

P R E L I M I N A R Y

CP6003-SA/RA/RC

IPMI Firmware

Doc. ID:

1045-5656, Rev. 2.0

January 12, 2012

This manual is related to the following products:

CP6003-RA IPMI CP6003-SA IPMI

Table of contents

Document Outline

Revision History
Imprint
Disclaimer
Table of Contents
List of Tables
- 1 Terminology and Acronym Definitions 9
- 2 Related Publications 11
- 3 Standard IPMI Commands 15
- 4 AdvancedTCA and AMC Commands 20
- 5 Get Device ID Command with OEM Extensions 21
- 6 Set Firmware Parameters 22
- 7 Set Control State 23
- 8 Get Control State 24
- 9 Sensor List 25
- 10 Gigabit Ethernet Link Sensor Assignment 27
- 11 Thresholds - Standard Temperature Range 28
- 12 Voltage Sensor Thresholds 28
- 13 OEM Event/Reading Types 29
- 14 IPMI and Hot Swap LEDs Function 45
1. Introduction
- 1.1 Terminology and Acronym Definitions
- 1.2 Related Publications
- 1.3 IPMI Overview
2. IPMI Setup
- 2.1 IPMI in a CompactPCI Chassis
- 2.2 IPMI Setup for the CP6003-SA/RA/RC
- 2.3 IPMI Setup for the Rack
3. IPMI Controller Hardware
4. IPMI Firmware
- 4.1 Key Features
5. Supported IPMI and ATCA Commands
- 5.1 Standard IPMI Commands
- 5.2 AdvancedTCA and AMC Commands
6. OEM Commands and Command Extensions
- 6.1 Get Device ID Command with OEM Extensions
- 6.2 Set Firmware Parameters
- 6.3 Set Control State (SPI Boot Flash, Boot Order)
- 6.4 Get Control State (SPI Boot Flash, Boot Order)
7. Sensors Implemented on the CP6003-SA/RA/RC
- 7.1 Sensor List
- 7.2 Sensor Thresholds
- 7.3 OEM Event/Reading Types
8. IPMI Firmware Code
- 8.1 Structure and Functionality
- 8.2 uEFI BIOS/IPMI Controller Interaction
- 8.3 IPMI Firmware Configuration
- 8.4 Firmware Identification
- 8.5 Firmware Upgrade
- 8.6 Setting the SEL Time
- 8.7 IPMI Firmware Write Protection
9. FRU Data
- 9.1 Structure and Functionality
- 9.2 FRU Version Identification
- 9.3 Board-Specific FRU Data
- 9.4 FRU Data Update
- 9.5 FRU Data Write Protection
10. XMC Card Support
11. uEFI BIOS Failover Control - Automatic SPI Boot Flash Selection
- 11.1 Automatic SPI Boot Flash Selection During the Boot Process
- 11.2 OS Boot Order Selection by OEM IPMI
12. Hot Swap and Shutdown
- 12.1 Hot Swap Handle and Hot Swap (Blue) LED
- 12.2 The Hot Swap and Shutdown Processes
13. LAN Functions
- 13.1 Overview
- 13.2 Setting Up the Ethernet Channel
- 13.3 Basic Setup from uEFI Shell
- 13.4 Setup by “ipmitool” or IPMI Commands
- 13.5 Setup of User Accounts and Password
- 13.6 IPMI Over LAN (IOL)
- 13.7 Serial Over LAN (SOL)
14. OS Support / Tools
- 14.1 Linux Tools
- 14.2 OS Support - Board Support Packages
15. IPMI and Hot Swap LEDs